Bought BR600 replacement carb Amazon- China $22
Bought a replacement carb for BR600 from Amazon (China) and it worked, but took some engineering. When i first put it on, I noticed one of the hose connections was not as curved as it was in the old...
View ArticleWalker won't turn over- ground problem, but can't find it
I have walker mower that won't turn over. I traced it down to a problem with the safety ground circuit. I have 12 v to the yellow (from ignition switch) and red wire on relay D, but I don't get 12V to...
View ArticleExmark Metro 48 throws the main blade belt
So I have an Exmark metro 48 which keeps throwing the blade belt when I disengage the blades. I've changed the belt and readjusted the guides per specs in the manual. What could it be?
View ArticleScag Tiger Cub starting problems
I went to start the mower to bring it in for new oil and grease and it started fine. Ran out of gas so I refilled it went to start it again and nothing wont turn over. I replaced the fuses, checked the...
View ArticleDixie Chopper Silver Eagle Blowing Fuses
I have a 2008 Dixie Chopper Silver Eagle today while mowing my dixie chopper back fired then died. No power at all. So my husband found that a fuse was blown. We changed the fuse and he began to mow....
View ArticleHow would you replace a roof vent on an enclosed trailer?
I have a trailer that needs a new roof vent. The old one blew off in a recent storm. I am concerned with the weight of a person being on the roof, since it is thin metal. The two options I am...
View ArticleOil Drain Plug removal?? help
Ok, so I bought an older scag 52 inch walk behind this spring, and have been doing maintenance on it trying to get it ready for season. it has an older Kawi 14HP engine, and the oil looks pretty dark....
View ArticleEcho vs. Stihl
I don't know about the rest of you guys but as far as I'm concerned all of Echo's power tools are just as good if not better than Stihl w/ the exception of their chainsaws. Over the the winter I bought...
View ArticleBobcat help!!
I bought a used 52" walk behind just a couple days ago. Model #930303, the wiring is a terrible botched job. It appears the key switch went bad and instead of buying a new one they put a push button in...
View ArticleWhat Kubota diesel is in a Walker Mower?
Just wondering if you guys knew what a lil' diesel Kubota in a Walker mower would be, as far as a model or series number goes? I've got a 1998 that needs a new starter pretty badly, and I'm debating...
View ArticleDead Kawasaki
I have a kawasaki FC540V in a JD GT262, was running fine and just died...have replaced circuit board\key switch, coil, and spark plug, cleaned magnet on flywheel and checked key in flywheel...spins...
View ArticleKohler ch740s running out of patience
Hi all. Im new to this site and i had some questions. I have a 2007 scag mower with a kohler ch740s 27hp motor. Motor has spark compression good fuel and still wont start. Keyway is good on the...
View ArticleLost carb oring
I took the carb off of my scag tt ch25, disassembled, and ran it through the ultrasonic cleaner. I lost one of the little o rings at the accelerator pump. New accelerator pump kit with o rings is over...
View ArticleDolmar 251.4 brush cutter
Does know what the correct valve settings are on the Dolmar 251.4 brush cutters .
View ArticleWiring problem exmark
Hoping someone can help me understand where my problem is coming from. Exmark Lazer Z key switch would turn engine over. I by passed all of the safety switches by jumping them. I tested them first and...
View ArticleGood Info about Oil.
Hey guys, (and Envy in particular) I found this website that give the straight skinny on oils how they are made and why one type is better than another. It also dissects oil filters and why we should...
View Article23 hp kawasaki governor problem
changed crankcase gasket had oil leaking.After reinstalling engine on lazer z. I cannot seem to get the governor adjusted. Engine revs out of control.I adjusted the arm and the governor rod ,open...
View ArticleKawasaki FC420V ran perfect then stalled and won't start
I have a 1980s fc420v that was homeowner-owned and thus not used much despite age. I bought it last year and barely used it. Never a single problem. Always started in 2 or 3 pulls. I stored it in Fall...
View Articlehydro gear cross contamination ?
Any help appreciated .. I had a left pump go bad on a older exmark lazer z with BDP 10A 427 with TF parker wheel motors.. The thrust washer on left pump was in hundreds of medium size pieces and 1000s...
View Articlewalker mtefi 26h in line fuel filter
Hey guys back again I have a walker mtefi26 hp with a kohler command pro engine gas. wondering about the in line fuel filter. where it is and do I have to bring it to dealer because its a pressurized...
View Article