Scag Walk Behind - Adjusting steering controls
Does anyone know how to adjust these control handles on the Scag SWZT? I Tried loosening the bottom of the rod and the top of the rod and turning the rod to adjust the control lever on that side. I...
View ArticleWright Stander intermittently shuts off while mowing
Hey Guys I have an 09 Stander that all of the sudden has been intermittently shutting off while mowing. I can mow 6 yards and no issues and then on the next one it cuts out. If I shut the pto off it...
View ArticleDingo 323
Been having issues with it suddenly shutting down, but immediately restarting on the key. It's been a bit neglected as of late, probably because it's always been so reliable..... Anyway, figured I'd...
View ArticleGravely Pro Stance spring popping off
I have a 2016 36" Gravely Pro Stance. Model 994131 serial # 000177. Every so often but not every time, when I go to turn the blades on, the spring pops off the tensioner pulley. I am going to post some...
View ArticleCraftsman Garden Tractor Kohler 18.5 hp Twin Magnum Engine
I have a Craftsman 917 251 491 SN 022096C. The engine is MV18S. It does not pull gas. I blew out the lines into tank and towards engine. Not sure if it has a fuel pump but will not start. If I spray...
View Articlesnapper pro 61 walk behind...cannot find model number
Hey all, I am a rebuilder. In the winter, I rebuild snowplow hydraulics. In the summer, I build for next year...but only 15 pumps a week. Anyways, to take up time, I make it a habit of buying and...
View ArticleKawasaki 14.5 hp FS481 to 18.5 hp FS600 Conversion
Hello all. New account to this forum but have used the helpful information many times. A while back, I came across a thread showing how my 23 hp FH680v kawasaki could be converted to the 25 hp FH721...
View ArticleTurf Tracer Pump Leaking
View attachment 336093 View attachment 336094 Hey guys, got a hopefully simple repair question. I have a Turf Tracer S and last weekend I was pulling a leaf tarp with it and both the hydraulic pumps...
View ArticleKawasaki 23hp to 25hp conversion
I own an 03 Hustler z with a 23 hp kawasaki engine. It currently has about 1100 hrs on it and still runs great. My question is... When it comes time to rebuild the engine, is it possible to convert it...
View ArticleToro Slow Hydraulics
I have a ZX4800, model number 74830. The left side hydraulics take a long time to warm up (15-20 minutes). I have to go back and forth at low throttle to get it warmed up. I usually get a couple...
View ArticleTrouble getting replacement engine
Trying to replace Kaw Fh541V CS31. Tried Jacks but give up after waiting on line for awhile. Anybody got a suggestion? Send note to the following no reply after a day....
View ArticleClik here to view.
Cheap China carb........what is your experience
I got a $16 box which included carb, plug, fuel filter, gaskets and fuel line. This was for a 20 year old stihl BR420 that was in storage for a few years....
View ArticleWalbro WT-20 Carb problem ??
I have a Craftsman 16" Chainsaw that is in good condition other than the current carburator problem (Walbro WT-20). The problem is that the fuel coming out of the air-intake section of the carb, like...
View Article13 year old Hyrdo WB with 43 hours - Purchase Questions
So I found a Gravely 52" hydro walk behind with a Kawasaki motor and a sulky for $2500. The mower looks great and of course I'm going to give it a test run. I'm buying it from a mom and pop dealership...
View ArticleDo Safety Interlock Modules Go Bad?
I got an Exmark Viking 36 dual hydro mower. The mower previously had a blown engine so I swapped that out. All is working good except the safety switches. I need the machine to be grounded if the...
View ArticleGrasshopper 618 help
i have a 1999 GH 618. With a 2006 Koehler command 18. I have had this mower for 2 years, and when it was running was a great machine. Last year it started getting really sluggish. And I'm no mechanic...
View ArticleKawasaki FX1000v backfire
Hey all...1st timer. Anyone have some guidance on why my fx1000v is backfiring, only after it gets "hot"? New coils, oil is beautifully clean and doesn't burn a drop. I personally have not checked...
View ArticleJohn Deere Walk Behind just died, now won't start.
Hi everybody. So I have an older John Deere Commercial Walk Behind, 38". It's been a great machine up until recently. I went to start it to let it run for 10 min or so. Well it ran fine for 10 min then...
View ArticleOld Bunton 52, with old Kawasaki FC540V-S09 - Can't find info
Hey folks, I recently acquired this old Bunton 52" Belt Driven Walk Behind for a couple hundred dollars here in Orlando. I'm trying to locate parts for the Kawasaki engine on it, but can't for the life...
View ArticleProblem With New Pressure Washer Echo Bearcat PW4000
I had Kubota order me the Echo Bearcat PW4000. I open box, top of box looks like had some oil on it. Not much maybe a cap. Take pressure washer out put it together. I notice a small amount of oil...
View Article