Where to buy quality berings for still fs 110 r and parts
Looking for wholesale sites to buy small engine parts For still, all kinds of mower brands (engine rebuild, 19 kawasaki to weedeater, to Shindaiwa blowers Hibi cranes, hydraulics & cylinder parts...
View ArticleWelding Hood
Need recommendations for hood to go with the Lincoln 140 I am giving as Christmas present. I threw up a couple kinds fixed and auto shading. View attachment 333750 View attachment 333751
View ArticleToro Mower governor issues
I have a Toro Personal Pace with blade brake. Lately I have been having trouble getting the governor working right. When the blade brake disengages the spinning blade the mover over-revs at 3800 or so....
View ArticleBroken PTO clutch wire - JD717A
I have a John Deere 717A, now with nearly 2,000 service hours. The PTO clutch has been flawless. Today, after doing some routine maintenance work, I wanted to fire up the deck for a complete check. I...
View Article2016 Gravely 260 problems
Hello everyone I've been dealing with major issue on my new gravely 260 EFI. Throwing 337 code "crankshaft position sensor since I drove this thing of from the dealer. Has the symptom of wanting to...
View ArticleGas siphoning
I have TCG 22EA weedeater that after use it siphons all the gas that is in the tank to the engine block. I also have a poulan chain saw that does the same. I have cleaned and blown out the carb....
View Articledang zerk
Anyone got a good way to remove a grease zerk that the tip has broken off of? Thanks fer advice.
View ArticleSeafoam or other stuff in hydro system before fluid change?
I'm not much of a mechanic, so if this is a stupid question, i apologize. I bought a beater '06 tiger cub a while back and in an effort to cut expenses where i can, i'm going to start changing hydro...
View ArticleScag gas tank gage messed up
Only 3 years old and covered all the time. And they cost$64 View attachment 334401 View attachment 334402
View ArticleTrans fluid changing procedures
I use an 03 2500hd (130k), and a 01 f250 (93k) for landscaping and plowing. I just had both transmission fluid completely drained, ran a cleaner through it, and filter/gasket replaced. Now, from...
View ArticleToro Z3000 with FS691V not revving with blades engaged
I purchased a new to me mower, Toro z3000 2012 52" with the FS691V Kawasaki. 1300hrs. Engine runs great, very smooth doesn't burn oil. Hydros are great. The engine revs up to full throttle while...
View ArticleWHP 48A Tracking.
Morning guys. This mower is a monster. Start all the gear up once a week and ride around on them to jog them. Well I changed hydros and all maintenance on mowers and the tracking seems to be pulling to...
View ArticleExmark Kawasaki engine
Has anyone heard of any issues on these motors bending push rods? Low engine hours
View ArticleTips on cold starting carbed kawasakis?
Just as the title states I find on mine you have to do short 3-4 second starts and it will fire after the 3rd or 4th time, but if you hold it longer it doesn't want to fire. I don't understand, but...
View ArticleJust Bought Four New PermaGreen Triumphs; I have a few questions!
We just purchased four new Triumph riders to replace the Magnums that we had been using. We are very excited for the switch, but I want to be well prepared when season starts! -Firstly, any tips,...
View ArticlePTO switch
it has been cold outside so sometimes when i turn on the pto on my cheetah the blades don't go all the way up to full speed when i engage them at 3/4 throttle. i give it a bit more throttle and they...
View ArticleGrandstand 36"
Hi guys, so i got my Grandstand back from the repair shop, i had problems with one pump that seams to be having troubles keeping the speed up in forward and reverse, after they tested the pump and...
View Articlewalker mowers
I have run walker mowers for years but i have a 20hp that is having problems, i was woundering if any one else has had this problem or knows how to fix the machine The problem is the key swich will not...
View ArticleSecondary two stroke gear.
Good morning guys. I have some older equipment i'm bringing back to life since the last few days have been slow. Whats the number one difference (or tell tale sign) needing a new carb, or a new coil?...
View ArticleReplacement relay for Walkers
I was talking to a Walker tech recently and he told me of a potential and costly problem that could effect the Walker wiring harness when people purchase the wrong part to replace the Walker #6942...
View Article