Ferris is2100 stalls when lifting handles
I have a ferris is2100 with vanguard 32. It stalls when lifting handles, never does it when cold. Can use it sometimes for a couple weeks no problem, then suddenly will act up sporadically for few...
View ArticleNeed Help! Kawasaki 19hp. FH580V-DS28-R
I can be mowing and It will cut out and start bogging down for no apparent reason and sometimes it will go dead, other times it will catch back on and I can finish my yard. It doesn't matter if I am...
View ArticleReplacing a JD Z737
My JD Z737 is ten years old with about 650 hours. It has a 60 inch deck. We now our small orchard which has just a few acres. I have looked at JD Z930M as replacement. Have also considered Swisher. I...
View ArticleScag Wildcat
I have a scag wildcat stwc52v-26ka-lc replaced engine last year with just over a 1,000 hours (Kawasaki) think know might be having problems with the Hydraulic pumps looks like might have a leak bit of...
View ArticleBunton spindle repair
I have a 72" Bunton mower and I'm trying to rebuild the mower deck spindles. Need to open this broken one to find bearing size to repair one not broken View attachment 331460 View attachment 331461
View ArticleHelp on wiring a new engine to my Skag walk behind
I have a Skag walk behind mower, model # SWZ48-14KA, with a FC420V-HS09 Kawasaki engine. By recommendation from a dealer I purchased a FX481V-S01-S to replace the old engine. I need help wiring the new...
View ArticleHELP PLEASE!!!!! Kawasaki FH580V
Hello, I have an Exmark zero with a Kawasaki FH580V. About three weeks ago it started surging really bad. It was still running okay once we started mowing so we figured we would look at it that...
View Articleecho bogged down under powered
echo equipment was bogged down and slow. tried pulling spark arester off. adjusting the carb and still bogged down. seen the carbon in the exhaust port. scraped it out with screw driver and pick. ran...
View Articlehow to purge pump if no release lever?
I thought I'd try to change filter and fluid once more on great dane surfer (48) before I tackle rebuilding pumps. It barely moves and very jerky with no power to climb trailer ramp (motor runs fine)....
View ArticleLooking Programmable hour meter for diesel mower
Looking for a maintance hour meter were I can program meter to blink light for each, every 8 hr for grease, 24 hr air cleaner clean, 50 hr oil change, hydrolic oil service I Google them meters but...
View ArticleElectric start briggs and Stratton
I've been told that a recoil start motor will start as long as fuel is present disconnected from a mower and all of it's wiring. My question is if i disconnect an electric start from the mowers wiring...
View Articleswapping 1 kawasaki electric start for another
I have a mower with a 23 HP Kawasaki electric start which through a rod through block right next to Starter. Just wondering if another Kawasaki electric start 17 HP will work with same wire harness....
View Article26hp efi walker
My walker was running rough , I've replaced fuel pump. Now I have fuel standing in one of the two chambers of the intake and it's bogging down like it's flooded any help would be appreciated
View Article1985 9 HP B&S need electric start
I recently purchased a 1985 Jacobsen seeder model 524 w/ a 9 HP I/C cast iron bore engine. This Engine - model 233452, type 1152-11, code 8507191 - is difficult to pull start. 1. Is there an add on...
View Articlequestion on wheel motor..
Great Dane surfer 48" -Should a wheel motor turn 'smooth' or 'jerky' as you turn it by hand slowly (still hooked up) with the mower raised off the ground and off? Mine turn very jerky as I slowly turn...
View ArticleTemp gauge for a air cooled 35hp vanguard.
Need something for my leaf loader because I have it boxed in on 3 sides.
View ArticleHustler Super Z fuse issue
Have a 2007 Hustler Super Z with a Kal 25 horse. The 15 amp fuse keeps blowing. Any suggestions as to why?
View ArticleExmark Navigator Steering and oil consumption
Hello all. I recently purchased a 2005 Exmark Navigator NAV27KC with the 27HP Koehler with 1000hrs on it. I have 2 questions. First, the steering is kind of messed up. Not the simple adjustment on the...
View ArticleJohn Deere X485 EFI issue
I have a Deere X485 and the fuel pump will not start. All 3 grounds on ECU are good. Incoming power to ECU is good. Fuel pump relay is not receiving ground from the ECU. I can jump fuel pump relay to...
View Article