Engine stops running when hot
my kaw 15 hp stops running when gets overly hot Cools off starts and run a while What should I be looking for ?
View ArticleWalker 26efi safety problem
I have a 2000 Walker 26efi with a starting problem. I've isolated it down to the safety switches I believe. Anybody know how to override them so I can make sure? The starter spins but there's no spark...
View ArticleWalker MC dies when I push the forward speed controller or engage the blades.
When either limit switch on the FSC arm or the PTO arm are closed, it kills the engine. I have replaced all three relays, and still the problem persists. Does anyone have any ideas what could be...
View ArticleIs echo equipment set super lean from the factory?
The last two new echo's I've bought have needed to be adjusted after about 50hrs of use. It only took about 1/4 turn to get it to run at full rpm because after a while it would only go to about 90...
View ArticleASV RC30 will not go forward
Hi everyone. I am new to this and looking for help. I have a ASV RC30 that will not move forward. All other functions operate normal. It will go in reverse, but not forward. Nut even a hum or anything...
View ArticleFiguring out which switch is bad
I hop on lawn mower, turn ignition switch, nothing. Test battery, good. Replace ignition switch, nothing. Remove solenoid, take in to Exmark dealer, they test it. Tested good. I am able to start mower...
View ArticleBriggs Stratton 380 Stop Wire placement
Hi Guys My first post here as I'm chasing some help. I have a weedeater lawnmower with a Briggs Stratton 380 ( 98902 ) engine. Long story short, I dismantled it and have managed to get it all back...
View ArticleWalker mtghs 48" deck gearbox bearing question
I picked up a well used Walker cheap. Was told by prior owner it needed new snap ring on deck gearbox shaft. It did. But my question.... the bearing that actually sits in the bottom of the gearbox...
View ArticleExmark 30" Aerator Problems!!!
We have the new Exmark 30" stand on aerator and was wandering if anyone else is having problems with the drive belt breaking? We had the first replaced at 17 hours and second at 20 hours. We are not...
View ArticleHelp w/ Hydro Gear Bypass Valve
I'm doing the first Hydro Gear (HG) service on an Exmark ZTM. Systems was drained / filled (new oil / filters)...I'm Now onto purging air from system. When I open the bypass valves, only the right...
View ArticleKohler ecv940 blowing up due to exmark design flaw
Has anyone else had problems with the Kohler redtech ecv940 engine blowing up on their exmark? The way they have the engine sit in sideways with the head next to the hydro causes it the valves to stick...
View ArticleSpark arrestors on muffler
I need good way to get the strip heads on the screws that covers the spark arrestors to clean them. They been plugging up lately.
View ArticleKawasaki Engine won't start - pullstart
I am having issues with my 14hp Kawasaki pull start OHV engine on my John Deere GS45 walk behind. When I pull the cord, the engine doesn't even seem to be trying to crank. Ill-advised I'm sure, it took...
View Articlesimplicity zero turn trouble starting
I have a simplicity zt 3500 48 inch deck with 27 hp Briggs and stratton engine it runs fine then all of the sudden it will not start. I took it to dealer and they pretty much replaced everything but...
View ArticleHelp- what's wrong with my scag deck?
I'm having an issue with my scag tiger cat 61" velocity deck. The closed end of the deck is leaving a small "brown strip" of grass . I've tried new blades, sharpening blades, different mowing heights...
View ArticleBent Scag Velocity plus deck
Have you guys heard of the deck being bent easily? The deck looks like it is built like a tank but the dealer tells me my deck was bent. I have owned this wildcat for 3 yrs and never remember hitting...
View Articlehydrro pump788067 311-2600L
Looking for a hydro gear pump 788067 - 311-2600L with no luck. Can anybody please point me in the right direction . thanks in advance
View ArticleJD Z920 repetitive starter issues
I have a 2010 John Deere Z920A that I keep having problems with the starter on. For the past 3 years, I've had to get it rebuilt each season. This is not a commercially used machine. It gets used on my...
View ArticleElectric testing need help
This module is off a XM3603 bobcat. I am testing it because it keep cutting out and not starting once i remove the ground wire the engine would run fine. I check the red an yellow wire and found they...
View Article