BOP Deck Idler Spring
on 36 inch single hydro deck. Cleaned out the pulley's etc. Idler arms were not functioning smoothly and one of my springs is pretty worn from rubbing the deck. Anyways flipped it the spring around for...
View ArticleHappy Fathers Day
Happy Fathers Day to all members. Try and relax today without having to work on any equipment. You deserve it!
View ArticleHelp - Kawasaki/Ferris Mower
I'm stuck on fixing a problem with Ferris mower and Kawasaki motor. Starts up and runs fine. On a hot day I can engage PTO and it will run very rough, some backfire, runs better with throttle pulled...
View ArticleCutting issues 44" Fastrak
First season using the 44" Fastrak. It's as high as it will go at 4" and I've tried at 3" and 3.5" too. It's leaving uncut grass and it doesn't matter how slow I go. I can go full speed and it doesn't...
View ArticleRepower, replace, or repair?
I have an old scag TT, the first year they made them actually. 1500 hrs. It has a CH25 engine, the no.'s aren't legible. I have blown a couple head gaskets lately on the left side. It has had a problem...
View ArticleLeveling Exmark Ultracut 60"
I have searched these forums and haven't seen to find an answer so I will ask you guys here. My Ultracut 60" deck is off by 3/8"-1/2" side to side and i am assuming this is what has been causing the...
View ArticleService Manuals
I was browsing the internet and came upon this unbelieveable site: http://needmanual.com When you get to the home page, there is a drop down for categories on the top of the page. There are thousands...
View Article14SB cord won't pull unless blade brake is engaged
Hey all. So I picked up a 14SB with a Kawasaki today!!! It runs but seems to have a clog in or near the fuel shut off valve. Can get any fuel out of it, but I can get it out of the bottom of the tank....
View Articleprocedure to switch out hydro pumps and wheel motors?
I bought a 61" Great Dane surfer to use for parts (got drove over by a vehicle) but it has good hydro's and wheel motors and was a running machine prior to mishap. My slightly newer 52" GD surfer has...
View ArticleSnapper Rear Engine Rider Re-power
I have a Snapper SR120 (I believe that's the name of it--I have the model # if needed) I want to replace the 8 hp Briggs and Stratton (that's seized up) with a 9 hp Briggs and Stratton engine off...
View ArticleReplacing CW hydro in Walker MT
I'm needing to replace the left (CW) hydro in my 1996 Walker MT after 1450 hours. I was wondering if anyone had some helpful insight on how to remove it. I can see that the battery will need to come...
View ArticleStihl HS 80 hedge trimmer service manual
Any thoughts where I might be able to purchase a service manual for the Stihl HS 80 hedge trimmer? I may have to disassemble my unit & would like to have a service manual for reference. My Stihl...
View ArticleKawasaki FB460V Ignition
I've read other posts here about the coil/igniter system and still have issues. No spark at the plug at all, if I use the gap tester it give a super small blue spark if I crank the gap down to...
View ArticleAnother 14SB John Deere question...
So i have my 14SB running today. It runs great!!! the blade brake is actually working, but the motor is sputtering and not sounding healthy when the blade stops. This tells me the bearings will need to...
View ArticleStihl Service and Parts Manuals PDF Downloads
Tons of Stihl Service manuals and Parts list http://www.worldoftrainz.com/Downloads/Files/Stihl/
View Articlerebuilding small equipment carbs???
does anyone really have any luck doing this?? i did 3 of them and none of them ran any better then when i started. 2 of them had no mixture screws so nothing messed up there. also 2 big shops by me do...
View ArticleBroke crank case 730v Kawasaki
2011 Toro Titian 54" Kawasaki fs730v 250 hours I heard a loud crunch and the motor stopped. The oil was a little low when I checked but not like oil starved low. What's back there that would cause this...
View ArticleTrans Belt / Pulley Problem with Gravely WB
Hi guys, I've recently purchased a used Gravely belt driven walkbehind. It's a 34" Pro-1334G, Model #988122. It's equipped with Pro Steer Handles. I've done a full tune up on this machine and have...
View ArticleFerris PTO clutch problem
I'm a new member here but have enjoyed learning from your collective expertise. I have a 48" Ferris 1500 Z, model number 5900680 with only 175 hours on it. Last year a stick severed both wires going to...
View Articlewaker ghs 20hp kohler wont shut off
it wants to shut off but just slows idle down a little. lower idle and choke stops engine and it starts and runs fine. replaced with new tested switch (walker 8960-15) the correct switch , problem...
View Article