Belt failure diagnosis
I have read a few posts on the forum recently regarding belt issues on walk behinds and riding mowers. I found this great belt failure anayasis guide from B&S on another forum that I frequent. For...
View Article5111 dies
I have a 5111 , it starts and runs fine, drives and lifts the arms, but dies as soon as I engage the blades switch?
View Article1993 Toro 580D Deck Motors
Are there any after market motors that will replace the toro motors? or maybe a repair kit?
View ArticleScag Turf Tiger won't move??
I have a Brand New Turf Tiger with just 28 hours on it . I was moving and Cutting just fine when I made a turn around to make another pass it just quit moving all of a Sudden. It won't go Forwards or...
View ArticleLesco belts
I have acquired an older Lesco that was left in the barn of a farm I purchased and have been tinkering with it to see if it is salvageable. It is missing a few parts including the belts. I am having...
View ArticleBlade Sharpening HELP
IMG_0884 by BradK HPLD posted May 25, 2016 at 9:29 PM So I bought a Bradley blade sharpener. But when I went to sharpen my blades the machine wont allow me to get the entire length of the blade. Is...
View ArticleCh25 no compression after HG replacement
I have a Scag TT with a ch25. The sticker with the engine spec nos is gone, but it's an older model, the first year they made the TT. Around 1600 hrs. I put around 50 hrs a year on it. I replaced the...
View ArticleExmark blade engagement
I've been googling this for 2 weeks now. I don't want to start another debate on engaging at 1/2 or full. However, mine won't engage at all unless its wide open. Once she is hot, it doesn't struggle at...
View ArticleExmark Lazer Z Breaking Mule Drive Belts
Hi Everyone, So I have a 2005 Exmark Lazer Z that is breaking mule drive belts. It seems to happen when I engage the pto at any throttle speed and happens at different time intervals from when the belt...
View ArticleFaulty Fuel Guage on new Hustler
The fuel gauge on my Fastrak SDX worked for a brief period when I first bought it. Now it stays either on full or at 1/4 tank no matter the fuel level. Ran totally out of gas and it was still on full....
View Article2007 scag 27kohler power loss
2007 scag turf tiger 61v 27ch kohler 74... Serial. I mini blocked this engine reinstalled parts correctly. Engine cranks runs good. Idle full throttle. Bogs down looses power but only with blades on...
View ArticleUsed "search"/ no luck Kawi LC 26.5 starter bendix
While using my mower to blow the grass off of my (long) driveway, the engine above labored hard for about 2 sec and then died. The starter would not operate after that. I found the fuse that goes to...
View ArticleToro Zero turn wont start with 2 week old engine
Hello friends, I have toro z5000 model 74370 with a kohler 20hp engine. I had blown the original 21hp engine due to an oil leak I didn't see from parking on grass. The original sv610-0020 was...
View ArticleDixie chopper flatlander xf 2500. Drive trans belt replacement B41
I need to replace my drive trans belt part number B 41. I bought the part from the Dixie chopper dealer today I put it on but seem to be intuitive but there is no diagram for the drive trans belt on...
View ArticleSTIHL TRIMMER FS76 (fuel tank cracked)
Hi every body, this is my first post in this forum, now happy to be part of it. I do have a Stihl FS76 weed trimmer, and it had been seated in my garage for several months, now I need it to work my...
View ArticleKohler CV14S problem !!!!complicated!!!!
Hey all, new to the forum, looking for advise... I am a trained Small engine Mech, though I never worked on the field, just spin wrenches for fun. So I am out of practice a bit... Question, I am...
View ArticleJohn Deere Z Trak z820a Hydro question
I'm trying to change the hydro fluid in my z820a. I've never done it before and can't seem to find any info online for this type of mower. Does anyone know how to do it and what needs to be done? I'm...
View ArticleClutch belt falling off pulleys turf tracer
Ive got an older turf tracer about a year 2000. This never used to happen but lately the short belt on the blade clutch has been falling off the pulleys. Not while its engaged. I replaced the belt it...
View Article