Km110r carb adjustment
I got a km110r powerhead that was stalling at idle occasionally and sounded like it had a miss at WOT. I've already cleaned the air filter and the muffler screen so I started tweaking the carb a bit....
View ArticleStihl Service and Parts Manuals PDF Downloads
Tons of Stihl Service manuals and Parts list http://www.worldoftrainz.com/Downloads/Files/Stihl/
View ArticleTecumseh HM100 governor setup
I recently picked up a well used chipper with a HM-100 engine. It starts up fine but once off choke, it wants to take off and over-rev. I shut the machine down, lubed the governor linkages, and noticed...
View ArticleFerris IS3000Z
So I picked up this Ferris IS3000Z with a Kawasaki FH721V over the summer as a winter project to fix up to have another backup and so far it has done nothing be stump me. I bought it none running and...
View ArticleCraftsman Stage 2 Snow Blower
So I aquired a Craftsman Stage 2 Snow Blower with a 7.5 Briggs motor. I got it for free and it had been sitting for quite some time so I did a quick clean out of it before trying to fire it up. I...
View ArticleEcho Edger has me stumped
got an Echo PE2400. Picked it up at yard sale for $25, owner said it used to start but now will not. Have some experience with these small two strokes so checked spark then compression (130), and then...
View ArticlePush Mower connecting rod and piston made of JB weld.
No I didn't do it, but some bored soul did. Surprisingly it lasted longer than I would have though. No doubt I love me some JB weld.... but dam! Connecting rod made from 100% JB Weld Link here.... Push...
View ArticleExmark velke rebuild kit
where can I find a pivot rebuild kit for an exmark velke. I have seen where I can buy each individual piece but was wondering if anyone sold them as a rebuild kit
View Articletoro z master seat safety relay
Does the seat safety on my 02 toro z master have its own relay or is it part of a control box? I shorted the writes on the sensor' so its not the sensor itself It starts and runs. Just shuts off if I...
View ArticleHydrogear Help?
The charge seal was leaking, so I got the kit and changed out the o-ring. I replaced the filters and fluid in both hydrogears. When I tried to purge the air, one side purged quickly and the other side...
View ArticleThinking about hiring an on site mechanic
The opportunity has arrived for me to hire a guy that has small engine repair experience. Hiring him would save alot of time going back and forth to my current repair shop and hopefully save me some...
View ArticleToro 580D engine swap?
I was hoping to get some insight from some of the mechanics out there. I have a '97 Toro 580D that, long story short, the engine block is scrap metal. It dropped a valve into the cylinder, which went...
View ArticleHONDA GX-120
Hello, I have a good running Honda GX120 to replace my 5HP Briggs on a TracVac lawn vacuum. I used it this fall with pretty good results however it seems to me the rpm should be higher. The suction was...
View ArticleUltra vac zero turn bagger
I have an Ultra vac detachable bagger with a newer Briggs pony motor. Has hose and side discharge attachment as well. Takes a 55 gallon trash can for a hopper. This unit works great compared to belt...
View ArticleExmark Lazer Z XP battery drain
I just bought an Exmark Lazer Z XP with the 27hp Daihatsu diesel engine on it. The engine has a blown cylinder head and I am working on rebuilding the engine on it. The mower has a new battery on it,...
View ArticleCraftman 1.5hp air compressor won't start under load
I pulled the compressor head and piston runs smooth up and down. With head on I can turn unit easily. I can start unit with no or low pressure(30lbs) and unit will build tank pressure fine. If I try to...
View ArticleWhat do you guys use/reccommend in your parts washer?
I just bought a jegs parts washer (part number Part Number: 555-81525). The instructions say to use water and dish soap only. I've read that people use mineral spirits. We will mainly be washing carbs...
View ArticleScag Heim Joints...Pricey
Why would the joints from Scag be worth $35? And ones on ebay be so cheap? View attachment 355336 View attachment 355337
View ArticleNew Predator Pro Kawi starting problems
Got new mower delivered early January. Ran enough to warm up but didn't get a chance to run it dry . Planned on doing so but got hit w a big snowstorm and was closed in the garage for a cpl weeks w...
View ArticleHydroGear Wheel Motor HGM-12P-7172 Shaft Seal
I need help in finding shaft seal No. 5 in the diagram. View attachment 355355 Got this from Hydrogear web site View attachment 355356
View Article