Woods 6215 hydro question
I am working on a 6215 woods that late last season completely lost one hydro all at once. Pulled strong and just acts like oil is bypassing somewhere or something not turning internally. Wheel free...
View Article20x8x8 tires???
ive been looking for a set of 20x8x8 tires with agressive tread and i cant find any. does anyone know where i can get a set ive looked everywhere! the more agressive the tread the better. even a set of...
View ArticleKohler CV15HP carburetor Leaking Gas
I have taken the carb off and cleaned it as best I could. Used tooth pick on seat. Still leaking so we have to turn gas off on every shut down. I understand carb well over $100. I came across this one...
View Article2001 Isuzu NPR-Gas Heater Core
Help! I am replacing my Isuzu 2001 NPR-Gas Heater Core, but can't get it out. I've removed the hoses, loosened everything up that I can find, but I can't get it out. Any suggestions or links? I can't...
View ArticleStarter solenoid engaging when battery connected
I have a Snapper Pro with a Kawasaki fx600v. It has 250 hours and since purchase at 9 hours the starter solenoid has been sticky sometimes taking several turns of the key to get it to engage and not...
View ArticlePump Reseal Questions
Hi guys, I'm in the process of resealing the hydro gear pumps on my Cub Cadet M48 mower. I purschased the mower used and the pumps were leaking pretty badly based on the amount of oily crude around...
View ArticleScagg problem
Hi my question may seem basic but I am from down under Australia I own a scagg mower love it model tiger It seems to be hungry for fuel when under mowing load replacing fuel filter but how do I undo...
View Article915b 7 iron idlers and spindle
I lossened the belt to check the deck over and found both idlers have a bit of play in them and the left side spindle has a little play and is gritty. Mower has 93 hours on it with warranty till July...
View ArticleBR600 idle Adjustments?
I've got 330 hours on my br600. Just, since i changed the fuel filter it doesnt like to stay running on idle after i've been using it for a while. When i first start it for the day it will run idle...
View ArticleExmark Lazer Z XP battery drain
I just bought an Exmark Lazer Z XP with the 27hp Daihatsu diesel engine on it. The engine has a blown cylinder head and I am working on rebuilding the engine on it. The mower has a new battery on it,...
View ArticleV-Ride owners Watch Deck Shaft Bearing Wear
I noticed that the 4 decks chains were not tight during the summer. I found the deck lift shaft bearings was wore out on spring side. I adjusted deck as best I could. Got around to replacing them...
View ArticleScag turf tiger stt61a-27ka electrical issues
Hello I’m new to the site and hope someone can help . I have an older 61 in turf tiger with a 27hp Kawasaki. I’m stuck on the electrical issues I’ll start from beginning. New starter installed had bad...
View ArticleStarter Fluid + Toro Power Max HD 1028
Hey guys so I will just jump right in... it is getting cold outside and thought I would attempt to start my snowblower and get it ready. However, I have had no luck getting it started. I recently had...
View Articlewhere to find parts for solo mist blower
I have a solo 451 mist blower. The screws that hold the motor to the frame vibrated out. I have not had success finding a place to order them. Any help is appreciated.
View ArticleCraftman 1.5hp air compressor won't start under load
I pulled the compressor head and piston runs smooth up and down. With head on I can turn unit easily. I can start unit with no or low pressure(30lbs) and unit will build tank pressure fine. If I try to...
View ArticleHarbor Freight Mini-Tire Changer
Is this thing worth $50 to change tires on small mowers....doubt it would work on TT 24W12-12 View attachment 355078 I watched utube on it that seems to show it working pretty good.
View ArticleVery slow leak in ZTR tire
60 inch Dixie Chopper. The rear tire leaks extremely slow. Goes flat in about 7 to 10 days just sitting. I cleaned it very well and visually inspected it but didn't find anything. I've sprayed it with...
View ArticleHomemade Trimmer Racks for Truck or Trailer
These are some pictures of the 2 position trimmer racks I made today. The base is just a piece of angle that used to be a bed rail. The uprights are from a old cheap home style weight bench. The...
View ArticleClik here to view.
2006 Durmax Transmission Cooling Lines Leaking
I have looked at repairs shown on utube and it looks nasty. I also seen the repairs showing cutting and flaring 3/8" line and using rubber line with 2 hose clamps? Has anybody tried that? Views are up...
View Article