Tecumseh transmission 3628-p1 for Scag 48sw dripping grease
There are couplers on each side of my Tecumseh/peerless transmission 3628-p1 for my Scag 48sw. One is leaking a few drops of grease. Can i grease this with regular chassis grease via the zerts? Or is...
View ArticleClik here to view.
Reel won't stop spinning on Mclane (heavy Pics)
Once I turn the mower on, the reel starts spinning w/o engaging the clutch. My mechanic has tried all sorts of tricks but to no avail. I am tempted to buy a whole bunch of new parts to see if that will...
View ArticleHello I'm Carey, I'm a retired excavator. Started working on small engines to...
I'm currently working on a 2013 Husqvarna 5325 zero turn. The left motor went bad. I've replaced left motor with a new one and still have the same problem. No power to the left side or Limited power. I...
View ArticleBad boy hydro issue...please help
anyone had this issue with their hydro? When I get on an incline and sometimes when turning, the machine does the jumpy skip type like the wheels are slipping but they aren't. Does that make sense?...
View ArticleHelp with Walker!
Hopefully someone can help me I'm ready to go crazy. I was having problems with the mower starting and thought I had it figured out but went to start it today and it just beeps won't crank over at all....
View ArticleSurging hydro/wheel motor
Hoping someone can help on an issue I am currently having with my Toro Z-Master. There is something going on with the left controls, when I try to drive, nothing happens on the left side until I have...
View Articleace mechanic donyboy rebuilds chainsaw top end
i never post in this section so donys probably already well known but if not heres a link to one of his vids of which he has 100s more that are all valuable info
View ArticleGrasshopper 721d cutting uneven
When the trim side meets its uneven just trying to get some ideas. Here is a couple of pics thanks. You may have to zoom in. It's got new blades and I replaced the spindle bearings also. View...
View ArticleIssues with FS90R
I first purchased a FS90R about 6-7 years ago. Until now it was used very little maybe 10-15 hours during that 6-7 years. Now its used more and has about 25 hours on it. I started having issues with it...
View ArticleChanging oil,belts,blades
What is the normal maintenance schedule you use, I'm thinking .monthly to change or sharpen blades, oil monthly, belts inspected weekly. Thanks for the help. Also it'll be a small operation. So I will...
View ArticleSharpen or Replace
Blades have 20-25 hours on them. They were new when installed. Are they worth sharpening with the damage on the tips? Glad I ordered 2 sets when I did. View attachment 347072
View ArticleRyan LawnAire III oil capacity/need to find manual...help!
I recently purchased a Ryan Lawnaire III walk behind aerator. I am going to change the oil prior to my busy aeration season. However, I am having trouble locating an operator's manual. So, before I...
View ArticleFx651v Kawasaki not running smoothly out of no where
So out of no where it started... idle slightly up and down up and down. Full throttle the same. If I choke it approximately half it smooths it out. Checked air filter and ran without air filter and...
View ArticleSnapper One of best 36" walkbehinds
Got two of these and today broke the crank in Kohler CV15t that was rebuilt in 2010. Unit about 20 years old original spindles and all hydro components. Seemed like the end until we found a Briggs...
View ArticleToro 22"" recycler personal pace Just Won't Start!
And I've tried EVERYTHING i can think of to just get it going. I feels like it has strong compression. The spark is strong (visually verified from the spark plug itself). I even put starter fluid...
View ArticleStihl km91 bogging issue
2 of my km90s finally died on me so a few months ago I bought a km91. Ran fine up until last week. Started to bog down after running for 5 mins. Let it cool down and runs fine for 5 mins again bogs...
View ArticleHelp please with Jojn Deere GX1320, won't start, need manual. Thanks!
I bought a used GX1320 and the first year is ran great. Last fall it started to die once it got warm, say after 15 minutes. Once it cooled off, a couple hours or overnight, it would start up again...
View ArticleBriggs Fuel Pump Diag
So I had another post about this same engine (link below). It has a no start issue as well. It will run on starting fluid but not without. I pulled the carb and it was bone dry. I gave it a good...
View ArticleHonda GXV530 16hp Engine
Hi, I had recently purchased a used Compact Power Powerhouse Prodigy. I used it about three times and then the engine blew. It looks like one of the rods broke and came through the engine block. The...
View ArticleKawasaki 25.5hp (FX801V) Valves
I have a Country Clipper Charger with a Kawasaki FX801V 25.5 hp with 675 hours on it. Recently been hearing the valves making noise and getting worse. Took it to the shop and they confirmed it was the...
View Article