oil/dust seal leaking.
this is on a kohler command CV18s. the oil seal (where the power take off comes through the oil pan) is leaking. how do I go about changing the seal? do I have to take the oil pan off? or can I do it...
View Article2 cycle oil mixes
I currently run all stihl equipment but a friend gave me a case of the red armor 2cycle oil mix that echo and shindawia sell is it ok to put in stihl equipment I have always used stihl 2 cycle oil. Thanks
View ArticleKawasaki FH430V Loping Problem
I recently purchased a 2004 eXmark 36 inch Turf Tracer HP that had a Kawasaki FH430V 15HP engine. At low rpms the engine sounds like it is going to die at higher rpms the engine runs fine. The...
View ArticleAnyone good with Kawasaki engines?
have an old scag mower engine runs good when throttle stay in right position. It's a 15hp , model is fh something I think gotta check. Starts first pull if you throttle it up it wants to clunk out if...
View ArticleCraftsman Mower to light utility vehicle.
We have a Craftsman mower that had a Briggs 18HP 1 inch shaft engine in it. I say had because it threw a rod through the block and is now a heap in my garage. New engine is about 500.00, short block...
View Articleecho 755h blower won't start after it gets rained hard, finally found a fix.
So I unintentionally found a fix for my blower that won't start if it gets wet. I had my hand on the spark plug boot when I started it and that pushed the boot down more and it started! Sometimes that...
View ArticleMower Throwing Deck Drive Belt
I've have a commercial John Deere 717a. It is a 2007 model with about 800 hrs. The last year or so, when I engage the PTO, it throws my deck drive belt off. Doesn't do it every time but fairly regular...
View ArticleLesco Spreader Axle Bushing
Rebuilding a spreader at the high school and there are no axle bearings in the pockets. The parts list calls for a composite bushing, and the pockets have zerq fittings. Does anyone have a picture of...
View ArticleScag Kaw 22hp FD661D shuts down while mowing
Hi, I have a Scag TT with a fairly new Kaw 22 HP engine, model @ FD661D-ES02. Recently, it started shutting down on me when I'm cutting. It's intermittent and it starts right up again. It seems to only...
View ArticleBR600 odd shutdown now no compression?
My BR600 has been on light duty homeowner use since I got out of the biz in 2009, its always run perfectly all the way up until today when I shut it down. It was running normally but when I turned it...
View ArticleGrandstand Deck hard to lift
I have a Toro Grandstand model 74568 serial 290000366. The deck is getting really hard to lift. Was wondering if anyone has seen|had to fix this. Hoping Ricky86 will see this. He is a Grandstand master.
View ArticleKawasaki Fx1000v Engine Problem!
Hello all. I have a Cub Cadet Tank S 7237 with a 37 hp Kawasaki Fx1000V. It has about 210 hours on it. I bought the mower as a repo from a bank when it had less than 50 hours. It looked almost new and...
View ArticleDitch Witch 1420 engine
I dont know where to ask about this kind of thing, so i figured id give it a try here. =) i have a Ditch Witch 1420 with a Kohler engine on it, ( dont know which engine) looks like a K241 Gas. but the...
View ArticleDitch witch engine
im sorry if i am posting this in the wrong section, i have a ditch witch 1420 with kohler engine on it (looks like a k241 gasoline) i was just wondering if anyone knew if you can replace the kohler...
View ArticleKohler ch25 blowing oil out breather
I have a kohler ch25 on a saw mill I bought it's a horizontal motor seems to be running good I changed oil and replaced the centrifugal clutch and now when I start it once rpm builds it's blowing oil...
View ArticleFX850 regulator problem
I have a 2011 Super Z around 114 hours. Last year I noticed one of the 3 wires on the regulator kept slipping off causing the battery to drain. I noticed the coupler was a little melted making it easy...
View ArticleBobcat Leo Model #942282 - need transaxle
Have a Jacobsen built Bobcat Leo zero turn. The right transaxle is frozen. the transaxle itself is part number 4129341 which is the updated part number (original part number was 778-043). New unit...
View ArticleVapor lock? Snapper mower 3.5 Briggs.
Have a very old (mid 80's!) Snapper 21355P (serial number 84260980) self propelled with a Briggs 3.5 engine on it, I think the sticker says "Max". It had been having issues with flooding the carb for a...
View ArticleEaton Hyrostatic Rebuild
Ran into some issues rebuilding an Eaton 778 right angle hydro. trans. Turns out the company discontinued the parts and none of the local places have any in their bone yards for parts. The only one I...
View Articleadjust combination throttle/choke cable
i have a Husqvarna ( 2009 ) engine model 445577=0110-1187-b1. this model operates both the throttle and the choke. can someone explain the proper procedure for adjusting the cable? or is there a video...
View Article