Engine for old 21 inch Snapper!
What replacement engine and where can I get for my old 21 inch Snapper!
View ArticleKubota w5021 parts, EMERGENCY
Hello, My name is Brian Murphy, I am extremely desperate and could really use some help. Some background: I have a commercial Kubota W5021 that was purchased new in about 1990 by myself, two brothers...
View ArticleNo power going uphill
I bought an older (2003) 48" Toro proline walk behind. It cuts like a boss for being the age that it is on flat surfaces, but it won't travel on anything other than a flat ground. I replaced the drive...
View ArticleBOP Parts Interchangeability
I'll start this thread to assist users in the future. 10579-S Multi-Disc Clutch/Brake is NORAM PN # CB190 Fits (2008-newer) Quick 36 (2009-newer) Quickie 32 and all Quick 44. Call (414) 267-4000 to...
View ArticleMower won't turn off
this seems like an odd problem to have, but starting today my scag walk behind doesn't turn off when I turn the key and remove it. I've been able to get it to shut down by pulling the choke and reving...
View ArticleExmark turf tracer battery die
Hi i put a fully charged battery on the turf tracer kawasaki mower in the morning. By later in the day the mower wont start. Jump start it. Pto works. Let it run to the next job site the pto wont work.
View ArticleExmark Navigator deck noisy
I have an Exmark Navigator (42" deck)and it seems to me the deck is awful noisy. There are no belts running the spindles so they must be gears but I can't find any info in the manual about lubricating...
View ArticleEcho vs. Stihl
I don't know about the rest of you guys but as far as I'm concerned all of Echo's power tools are just as good if not better than Stihl w/ the exception of their chainsaws. Over the the winter I bought...
View ArticlePump shaft seal failure Exmark lazer Z
Hello. I have a LAS28KA604. It was gifted to me after my grandfather-in-law rebuilt it. Since he dropped it off the right side hydro starts weak and he told me to go forward and reverse then it seems...
View Articlestihl hs 45 hedge trimmer starts & idles, dies with throttle.
I'm stumped. It starts on the first pull and idles fine. When I pull the trigger, it revs up and the blades move, then it bogs out in 10 seconds or less. I checked and tweaked the hi, low, and idle...
View ArticleRE-POWER----Honda ? Yamaha ?
ok i have a 48: Scag TIger cat ZTR. I love this machine and i love the cut that a SCAG delivers. The 22 HP Kaw let loose about a year ago. My dealer said to try the Brigs and Stratton Intek that is 27...
View ArticleFs80 vs fs94 vs fs 111rx
I'm wondering what everyone thinks of the new fs 94 or 111rx. I am currently using a 90 and 100 rx on my trailer. I have a 80 as a back up in the shed. My buddy offered me 150$ for the 80. Should I...
View ArticleLazer Z wheel motor possibly going bad
On the same side that I rebuilt the pump on, when I give light stick to turn or move forward only, I get a vibration and ratcheting or jerking on the wheel. Medium or full stick is smooth. It's only...
View ArticleKohler command pro 23.5 horizontal major oil leak
Bought an exmark LZ 60 with a fresh 23.5 ch730-3225 motor. Cut great no issues until all of a sudden after a few weeks it started leaking somewhere on the front of the motor behind the seat. Since the...
View ArticleCub Cadet Tank M54 stuttering or jerky on left side under load
My Tank would stutter, strong jerky action maybe 5 or 10 times a second. It only happened under load on the left side, when starting moving, uphill, on a side slope with left wheel to the bottom, etc....
View ArticleExmark Quest Belt Squeal
Hi. I have an Exmark Quest with 65 Hours. The last few times I cut grass I could hear a squeal sometimes coming from the pulley on the engine (squeal was coming from behind me so I assume that is where...
View ArticleScag swz alternator requiements.
How big of a alternator do you need on a repower engine to power the scag ogura clutch?
View ArticleKawasaki valve adjustment
2010 gravely pro stance mower 2010 Kawasaki FX600V engine 370+hours Pulled the valve covers to replace gaskets which I've heard are prone to problematic leaks on these motors which might be all I need...
View ArticleTool To Pull Echo Carb Plugs
This is the tool for removing plugs in Echo carb...2.5mm 91075. It has reverse treads just screw it in CCW and pop them out. Almost all echo have at least one and most of high end have two. View...
View ArticleEcho pb755 won't run in the rain.
Anyone have any of these? I've have two of these and have talked to two dealers, both of them say, well we can't control what the weather does. Really?? I went ahead and did what they said which was...
View Article