Clik here to view.
Honda HRX smart drive
Hi, can anyone reference on how to put together the smart drive pictured below. I broke it off, replaced parts but cant figure out how to put them together to have the control working properly.
View ArticleHydrogear ZT Transaxle Hours
Just wondering what kind of problemless hours you guys are getting out of your Transaxles on z's. If you could state hours and model 3100,3400,5400 ect. And any failures/ problems ect. Thanks!!!!
View ArticleHRC216 vs HRX217, specifically transmissions?
Hey, I've been through a few of the Honda HRR216's. They cut great, fire up in one pull, and the transmission starts strong but gives out after a few months of daily use. What is everybody's experience...
View ArticleKohler cv740 27hp command surging help
700 hrs on motor on ztr. When started, runs fine for 1 min. Or 30 min... idling..now when i engage blades or put mower under load.... it starts surging. So bad to the point it will die... it will...
View ArticleBad coil?
A few years back I had a Scag 36in walk-behind, and when I would get some tall or thick grass it would lose power and bog down. It started the second season I had the mower and it seemed to just get...
View ArticleScag Tiger Cat quitting after running a while
I have a 2013 model Scag Tiger Cat and I've never had any issues till the last month. Twice now in the last month it runs perfectly fine for 15-30 minutes then just quits all of a sudden. First time I...
View ArticleLiquid cooled Kawi overheat
boy I could use some help fast. I tried and bought a 2007 vintage lazer xs with a liquid cooled 29hp kawi. Today I smell something (turned out to be coolant) look down and it's red. I was driving it...
View ArticleMower vibrating after hitting rock.
The mower didn't hit the rock, but just skimmed over it. It seems like it has a bit of vibration now. Kind of made a buzzing sound going over it for a couple seconds then I backed up. I looked under...
View ArticleKawasaki FH541v engine problem
This engine is over 1000 hrs and burning oil. It is blowing buffs of smoke at high rpm. Plugs new valves adjusted new fuel and filter. Unit starts easy and both cylinders firing. Removed air filter so...
View ArticleRebuilding hydro gear
Is it possible? I have a gravely 152 and one side doesn't want to move. It will spin if tire is over the ground but nothing when back on the ground.
View ArticlePuller needed for redmax ebz8500 flywheel
Can someone tell me what puller they use to remove the flywheel from redmax ebz8500 back pack blowers? Thank you
View Articlehydro oil change in 36" gravely prostance
I am changing the hydro fluid in my Gravely 36 inch pro stance. I've drained the old oil got the new filters on got everything back together, purge plugs loosened, or but now I can't figure out how...
View ArticleHonda HRX217 ground drive speed selector cable replacement - help needed (pics).
The cable broke on my HRX217 today. I have a new one, but have found it difficult to install. I was told to take out the black panel toward the rear of the mower for access. The cable comes from the...
View ArticleKohler CV23S Running Very Rich
I've got a Kohler CV23S-75520 (S/N 3111936801) on a 2001(?) Dixon ZTR5023 (has about 650 hours) that is running extremely rich at all throttle speeds. Lower than half throttle it is visibly puffing...
View ArticlePhotos of a bracket I made for front hyd lift dethatcher
The dethatcher is 4' wide off of an old JD 185. Adapted it to fit the front blade quick hitch on my 455. View attachment 336334 View attachment 336335 View attachment 336336 Now to get fix a gearbox...
View ArticleBriggs Fuel Pump Diag
So I had another post about this same engine (link below). It has a no start issue as well. It will run on starting fluid but not without. I pulled the carb and it was bone dry. I gave it a good...
View Articlevanguard spark plugs
Just got a used toro workman with a 3 cyl liquid cooled vanguard engine in it. I pulled the plugs out and they are NGK BKR4E. However, pulled the manuals up on toro and it says NGK BPR4ES. Whats the...
View ArticleClik here to view.
Scag spindle replacemnt help..
Hello all, I bought this scag a few weeks ago for $500 I knew it would need spindles when I bought it, they have about 1/8" play. So no problem, I figure $650 I'll have a perfect machine. Now a few...
View Article