Scag turf tiger has me confused.
Hey gang, i am borrowing an older scag turf tiger from a friend while my lazer is getting repaired. I have been having issues with it. It ran great for a few days no issues then out of the blue it...
View ArticleShindaiwa EB802 problem
I have an EB802 that has fairly low hrs. The problem is it will have intermittent problems starting. It will start right up and run fine and then all of sudden the next time/lawn group you come to it...
View ArticleWhere to Buy Cheap V-Belt?
I have an Exmark Metro 36" walk behind, the v-belt part number is 1-323288, 49 3/4" x 1 1/8". I've checked out vbeltsonline, vbelts4less, vbeltsupply, as well as local parts stores and auto stores. The...
View ArticleJohn Deere L120 PTO Problem
PTO Clutch will not engage when I am sitting in the seat. I can get off the seat with the mower running (parking brake engaged) and turn the PTO will engage. This is backwards! Can anyone help?
View ArticleHow to Replace Exmark Metro 36" Spindle Bearings?
I'm looking for some help and tips on replacing my spindle bearings. I've searched YouTube, this site, and google, and haven't found exactly what I need. These two threads have good info:...
View ArticleScag deck release lever
Just got my Cheetah back from service and the deck release lever won't catch to make the deck stay up in its highest postion. Can anyone offer any insight with how to adjust because I dont want to take...
View ArticleScag Operator Controlled Discharge Chutes
Has anyone found a good operator controlled discharge chute for Scag Freedom Z 52?
View ArticleHelp with eXmark
hello all im new here so please bare with me. I have a exmark lazer z and after running it for about 30-40 min of cutting grass great the machine seams to bog down as if its being starved for fuel. has...
View ArticleStihl fs130r hard starting when warm.
The trimmer starts perfect in the AM get to maybe the third property & lots of cranking to fire it up, normal routine maintenance such as fuel lines,filters(fuel and air) breather, valve clearance...
View ArticleGrasshopper 725 suddenly dies and won't start.
This happens 2 or 3 times every year but this time I couldn't get it to restart. I was mowing along just fine and the engine died just like you turned off the key. Usually if I jimmy the park brake,...
View ArticleKawasaki FX751V Cuts Out/Dies
A few days ago, my JD Z830 started cutting out and would occasionally die. I've had this problem in the past and it was water in the gas, so I didn't think much about it. I drained the gas, put new gas...
View ArticleWhy Does My Walk Behind Squeal?
Its a belt drive.It only does it when going forward. When I squeeze the pistol grips and stop it stops. I have greased to grease points in the operators manuel with lithium grease. I dont actually have...
View ArticleRocks in my Walker!!
Hi. I ran over gravel and now the blade motor won't turn! What do I do? The engine turns on but the blade screams. I can't turn the motor by hand. I got out all the rocks I could. Is there a way to fix...
View ArticleHelp with a exmark
Tonight while mowing my right wheel locked up. I Unscrewed the release on top of the pump and started pulling the mower but the wheel will not turn. I finally broke it loose. Then the release plug...
View ArticleScag tiger cub solenoid location and bypass
My scag tiger cub won't start and just clicks when turning the key. Looking for the location of the solenoid to try and bypass it with a screwdriver to see if it starts. And how to use the screwdriver...
View Articleblade question for ferris is700z
What is a good replacement blade for this 52 in icd deck. And a part number and where u get them would be great. I bought a couple sets off ebay a while back. They are thin and wont hold a good edge....
View ArticleExmark pioneer s
I have a problem with the flat idler pulleys i live in west texas and its dusty here what happens is when dirt gets in the bearings it gets so hot the pulleys melt right off i mow commercially so this...
View ArticleMuffler Red Hot
View attachment 325237 View attachment 325236 Hi Guys, I finished the FD750 rebuild and got it installed and started this evening. I wanted to run it for at least 45 minutes to get everything up to...
View ArticleSprayer Gauge on wrong side?
Is it ruined? It is on the other side of the zero pin. I just noticed recently, it was working just fine. It tried to go, but the little pin stops it.
View ArticleNavigator belts broke and took the wiring harness with it!!
I have 2 Exmark navigators. My older one has broken belts a few times and just had to replace belts. My newer one I bought(EFI) a year or two ago broke the belts and when it did, it grabbed the wiring...
View Article