Still some air in Hydro's
Changes the oil in the zt5400's at 50 hours. Went through the bleeding procedures following hydrogear instructions. I still see some air bubble coming from on of the pump through the reservoir. So I...
View ArticleKawasaki fc540v-bs01
have a few question about my Kawi that I hope someone can answer. 1. I need new oversized rings for it I found part number 13008-6002 does anyone know for sure it these oversized rings will fit 2. What...
View ArticleSpindle nut keeps coming loose, help needed
Over the winter, I replaced all the spindle bearing in my deck with sealed bearings. I have mowed my 5 acres 4 times this year so far. Today, I got half way through mowing and noticed an uneven cut....
View Articlenew Walker ghs fill signal issues.
This is on a new walker ghs model T It started the issue at around 200 hours . The fill signal horn is designed to beep when the box is full but at around 200 hours it became a continuous on sound, yet...
View ArticleHave a 2011 wright stander with starting issue
I started it and turned the PTO on, mower turned off. Blades had been a little slow to engage last time or two. Now it will not start. Turn the key and nothing, no sound. I can trip the starter and the...
View ArticleLx 173 no spark.
Hello. I have a Deere lx 173 with no spark. Over the winter mice made a new home under my engine cover and chewed the spark plug wire and the other wire that connects to the coil comin from the voltage...
View ArticleMuffler Red Hot
View attachment 325237 View attachment 325236 Hi Guys, I finished the FD750 rebuild and got it installed and started this evening. I wanted to run it for at least 45 minutes to get everything up to...
View Article15w50 vs 20w50
the scag manual calls for 20w50 oil to be used for the hydro fluid. i can't find 20w50 oil except in regular oil. i want to use synthetic. mobil 1 has 15w50 but not 20w50. is it ok to use 15w50 for the...
View ArticleBunton 36" Walk Behind
Acquired a old 36" Walk Behind Bunton. Guy just wanted it out of his yard so thing doesn't owe me a dime, just a few hours worth of cleaning the carburetor out. Got the motor running good but having...
View ArticleSeat Switch
I was three lawns into my day yesterday when my mower (Lazer Z) started making a noise that sounded like the seat switch backfiring. So I turned off the mower and looked and sure enough it was the seat...
View ArticleSpecial Tool? Exmark mower
Hi, Is there any tool available to hold a pully on the mower deck while removing the top nut on top of spindle housing? Thanks Steve
View Articlez915b throttle
I bought a z915b and ever since new the throttle doesn't go forward all the way, there's about 1/8th of an inch more you can push it but there's a rivet that makes it come back to almost full throttle,...
View ArticleKawasaki fh500v carburetor problem
I have a 17 hp kawasaki fh500v on a dr brush trimmer. I'm needing to know how to reset all the settings, back to factory settings. It's not wanting to start, it's getting spark and fuel. Awhile ago, I...
View Articlequick 36 help
I am wondering if anybody can help me. I have a quick 36 36 inch hydrostatic mower built in North Carolina 2004. it has been sitting for about 4 years, motor was strong, but I need all the new hand...
View ArticleEngine swap?
Hi guys I am new here.. I am working on a Husquavarna WH4817 commercial walk behind with the 17hp kawasaki engine and it is smoking pretty good. Thing is I have a 18hp Kohler in a craftsman tractor...
View Articleolder lazer z hydro pump o ring replace??
my left hydro pump has a small oil leak and its only leaking at rear where the 2 o ring seals are. did anyone just loosen the 2 back screws of the oil pump and then the 4 screws that hold valve body...
View ArticleKohler 18ohv Oil coming out of breather hose into Air filter
Good Afternoon everyone.. I Have a Cub Cadet 1863 with a Kohler 18ohv.. When mowing the engine starts bogging like it is going to stall then backfires.. Ive notice oil coming out of the breather hose...
View ArticleJohn Deere x500 25 hp Kawasaki problems!
Hi I'm Josh new to the forum. I have been having problems with my x500 first it was surging really bad under load and sputtering. So I cleaned the carb adjusted mixture screws so it was running smooth....
View ArticleEXMARK Commercial 30' mower vibration problem
Turned in one of my 30" eXmark hand mowers the other day because it was vibrating. They couldn't figure out why, and decided the problem was I ternary to the engine. Kawasaki responded by offering to...
View ArticleExmark Lazer Z won't start sometimes
I have an Exmark Lazer Z; 2014 w/200 hrs: 60" deck, 34hp Kohler w/computer electronics: Recently, Sometimes, not always; after mowing for several hrs engine dies when I get off the seat (brake on, pro...
View Article