Cause/Fix for Backfiring??? (Kawi 31 Carb - 160 hours)
I have a 2016 Cheetah with a 31 Kawi (carb) on it. I dropped it off at the dealer for some warranty work, and to have the backfiring checked out. I just assumed the valves needed to be adjusted - quick...
View Article2005 Gravely 152Z engine change?
Hello everyone, I have had this machine since new to cut my 8 acres once a week over the past years. Faithfully changed Kawasaki 23 hp engine and hydro oil over the years and has just over 1500 hours....
View ArticleSmoke/Mist Coming Out of Oil Fill Tube!! Please help!
Husqvarna YTH22V46 8.5 hours. I just changed the oil due to there being water in the system of the mower specified above, opened oil dipstick/cap and there was a mist/vapor/steam coming out. Is this...
View ArticleKilled my Stihl Kombi shaft Questions
Was out using my Stihl Kombi KM131R today. Had the carbon extention and the pole saw on it. Was cutting my last limb then I heard a clunk noise and it stopped spinning. Broke the end of the shaft that...
View Article2005 Gravely 152Z starter staying engaged
Kawasaki FH680V - In the last couple of weeks, every so often, when I turn the key to start the motor the starter will stay engaged for a short time. More often when I start it the starter will stop...
View ArticleWalker blower Impeller Replacement
We have a very old Walker GHS 36" that we are doing some renovation. I am considering replacing the impeller if needed. How do I determine if it should be replaced? And will I have to pull engine to...
View Articleyahzoo belt issue
I wanted to replace the wheel drive belts on my KKW36121 The part number is 101956 I know husky bought them out the best that i could find for a replacemnt is husky number 539110 859 the issue is those...
View ArticleIs the Hitachi carb adjustable?
Curious if the carb on my Hitachi handheld blower is adjustable. I have looked and looked but I don't see anything to adjust except for the idle stop.
View ArticleUltravac 2 bag system on a 2014 52 X Series
I'm new to exmark and recently bought a new to me machiene with the ultravac twin bagging system. I threw a new blower belt on the pulley but the blower still seems to get clogged under modern leaf...
View ArticleFollow my engine swap? 44 proline
The patient: 15hp belt 44 toro proline This was my very first commercial unit. Great machine. Sold it to a family friend, local weekend warrior. Part of his agreement to buying it is I had to keep up...
View ArticleNeed help...fuel getting into crankcase on Kawa 17HP VTwin
Like title states, got a Exmark WB w/ 17HP V Twin - recoil start - hydro - 1000 hours - well taken care of. Ok, here goes..noticed oil like dripping out where muffler connects to exhaust..pulled oil...
View ArticleTransaxle not Engaging
I have a Bunton BZT3310 and after breaking one of the transaxles down and inspecting, and purging now neither wheel will engage
View ArticleEcho PAS Drive Shaft Problem
Hi All, I bought a PAS 265 power head (used) and the drive shaft needed to be replaced. I made the swap without a problem except the new flexible drive shaft does not stay in place. For example, if I...
View ArticlePoulan Chainsaw Primer Bulb Won't Press In
Hello. Chainsaw poulan model 3314 the primer bulb wont press in. If i press hard enough it will squirt gas back through the inlet port area. I tried dissembling the carb. I am suspecting its the carbs...
View ArticleGravely Pro-Turn 460 Hydro Change
I am coming up to the first 75 hour hydo change. I consulted the owners manual and there is a couple of terms I need clarified. It says to drain the fluid from the bottom oil fill port plug. Where is...
View ArticleToro 580D engine swap?
I was hoping to get some insight from some of the mechanics out there. I have a '97 Toro 580D that, long story short, the engine block is scrap metal. It dropped a valve into the cylinder, which went...
View ArticleDixie loses left side power uphill
Hi. I bought a used Dixie S# N220357 V# 177306VN218 C#64100-S 17-Mar 03 for what I thought was a good deal. Had to level mower deck and replace the blades. Seemed okay. Now when I go straight uphill...
View Article2005 Hustler Super Z Blade clutch problem
I've resolved my problem, but thought I would pass the information along for someone else's use. My super z blade clutch wouldn't always come on when I engaged the switch. Several on and off attempts...
View Article708cc predator engine question???
I have a 2002 exmark lazer hp with a 20 kohler command engine. Wanting to repower the unit with a 708cc predator engine. Have a few questions?? 1. The shaft looks to be a little short. Through may...
View ArticleEcho SRM-2100 - maintenance, parts, and serial #
I have an approx. 18 year old Echo SRM-2100 straight shaft trimmer that has worked well (for weekly residential use during the spring, summer and fall seasons). I've replaced the fuel gasket and lines...
View Article