Scag SW36-13kh deck swap?
my deck is fairly rotted but it cuts well in all conditions. I found a 52 solid deck complete. Assume it would cut the same? Unsure yet it it’s manual or electric pto. Mine is manual. To swap this 52...
View ArticleWater in pump oil
I was using my tank sprayer today and noticed a milky white oil in the clear pump reservoir. If water is getting into the oil what part failed or could this just be condensation with the cold temps? TYIA
View ArticleGood Info about Oil.
Hey guys, (and Envy in particular) I found this website that give the straight skinny on oils how they are made and why one type is better than another. It also dissects oil filters and why we should...
View ArticleLeak Testing Stihl 2 stroke Trimmers
So my first step was going to be buying these tools. Am I on the right track? View attachment 349016 This one for carb test View attachment 349017 Do I need both???
View ArticleBG86 issues
I have a 3 year old BG86 that runs flawlessly once started. The problem is getting it started. It acts like it floods almost immediately. The only way I can start it is to not choke, don’t prime and...
View ArticleFerris is 2100
Does anyone know part number for 2016 ferris is2100 spindle bearing. I have 247 hours and at least one spindle needs bearings. It is a 52 inch cut. Thanks...
View ArticleToro/exmark suspension seat dial
i have a 2014 exmark Lazer with suspension seat I bought used off a guy. The plastic dial where you select your weight spins free, gets hard to turn, then spins free again. Everything turns together...
View ArticleRear end squeak.
Hi guys, I’ve noticed while out in the bush today that my rear end on my 09 Silverado 1500 is sqeauking, when I got home I narrowed it down to either a u joint or differential input seal. It’s...
View ArticleKawi fx idle problem
Rpm started going up and down. Seem to only do when blade are not engaged. Smooths out while cutting. I dont know the actual rpm's but as an example its like 500rpm for a few seconds then 1000rpm then...
View ArticleEcho SRM-2100 - maintenance, parts, and serial #
I have an approx. 18 year old Echo SRM-2100 straight shaft trimmer that has worked well (for weekly residential use during the spring, summer and fall seasons). I've replaced the fuel gasket and lines...
View ArticleNeed help
Hey, I purchased an exmark radius 48 x series with an ultra vac system. The belt for the ultra vac is extremely tight. The tensioner pulley doesn’t make it easier to take off or put on. I have only...
View Articlewhat all in one hydro brand is on the exmark lazer z's
is it parker or hyrdo gear or something else?
View ArticleKohler Command Pro 27 about to head to the scrap yard LOL
I had another thread posted here about this motor. It wouldn't start and was spitting back fuel. I've solved the previous issue (fuel spitting back was from throttle getting stuck, I forgot to transfer...
View Articleanyone using echo pro rated dig saws?
Ok this is firewood season and tree work season for me. I've used stihl saws forever. Have had great service out of them. Im talking about pro saws in the 1000$ ranges. My local dealer is closing soon...
View ArticleWalker diesel electrics
Have 2 Walkers, 1 - MD and 1 - MC, the MC is for mowing (2 decks) the MD has a JoBeau chipper. I refurbished the MD a few years back and it's been operating very well. However I now have an electrical...
View ArticleToro 30137 WalkBehind Parts List
Does anyone have any parts diagrams, lists, etc for a Toro 37" WalkBehind - 1992 model 30137. I just picked one up, looks like hell, but it started first pull and cuts like a champ for being 17 years...
View ArticleTrans Belt / Pulley Problem with Gravely WB
Hi guys, I've recently purchased a used Gravely belt driven walkbehind. It's a 34" Pro-1334G, Model #988122. It's equipped with Pro Steer Handles. I've done a full tune up on this machine and have...
View ArticleClik here to view.
Kawi FX730V Blew Up
fx730v engine blew up today at just under 1200hrs. others on here have gotten a replacement engine free of charge because of a manufacturing defect so i'm hoping for the same.
View ArticleSmoke/Vapor/Mist Coming Out Of Oil Fill Tube. Problem?
I have a Husqvarna yth22v46 riding mower. Bought it on craigslist with 5.2 hours. Did the first oil change (and oil filter), then noticed a little later that there was white stuff on the dipstick....
View Article