What size it this bolt?!
I have a john deere Z710A mower. The bolt in the parts manual is also a M16 for the blades. Had to buy 50 dollar set to find the bolt socket. The socket for my bolt is a metric 24. I would have liked...
View ArticleReplacing Fx691v with Fx1000v
So I blew up a Fx691v and have the opportunity to replace it with a Fx1000v. This is going on a toro 3000 series with a 52 inch deck. Basically I want to know if this is doable and if it is, is it...
View ArticleJDeere LX176 Hydrolock/Cutting Out
Our John Deere LX176 riding lawnmower is behaving kindof oddly. Initially I thought that the grass was overloading the blades and killing the engine, but I have now noticed this happening while at idle...
View Articlebunton/john deere walk behind ????
I am sure this question is on here somewhere but i have an older John deere walk behind and doing research it looks like it may be a bunton the serial number is as follows John Deere TY4817D112764 I...
View ArticleWalker 25 Efi bogging down
My 09 walker 26hpefi starts to bogg down after about an hour of running. If I turn it off and restart an it is fine. Repeats throughout the day. Any ideas?
View ArticleMy old riding rear engine Snapper jurks...
... can someone tell me what might be and how can I solve the problem? Thanks a lot.
View ArticleKawasaki FH641V
I have a Kawasaki FH641V that sprays oil out of the tailpipe. It also sprays oil out of the oil filler tube. Knowing this, what would you all say is causing this, and what would be the fix??
View ArticleGravely Prostance 52" parts issues
Do they still make parts for the Gravely Prostance 52" 994112 models?? We've have been waiting on a skid plate and deck struts for about a year now. We asked our parts and gravely dealer guy if the...
View ArticleRunning to stall out of fuel doesn't winterize an engine
just making a point that so many online suggest to avoid ethanol build up, starting problems the next year, and carb gunk, just running the engine until it runs out of gas (or putting stabilizer in it...
View ArticleClik here to view.
tilt a horizontal Honda GX back = oil in gas every time!?
I have a Honda GX horizontal on my slice seeder that seems like every time I tilt it back, it floods oil into the gas and won't run. I have to drain all the oil and gas and clean oil from the carb and...
View Articletires rubbing frame on banks
Is it possible to put tire valve on opposite side,so i can reverse rims on back? I bought a new 52" lazer z x series and tires are way too close to frame .all exmark wants to do is put a half inch...
View Articletoro 20332 will not free wheel
Hello this is my first post, and I am just a homeowner that was given a Toro 20332 Recycler personal pace mower. Serial # puts it has a 2010 Model.The trans is new I just put it in today, the driver...
View ArticleEcho srm-210 carburetor adjustment
Hello folks, I own a srm-210 and I absolutely love it however I have an issue I cannot fix. Any assistance you can provide is greatly appreciated. When the trimmer is idle the head still spins. I've...
View ArticleWalker mower starter noise/spinning?
2003 MT 20hp Kohler 2900 hours. Been running great went to start it in the middle of the day today, turned the key and just heard a spinning/revving noise. Volt meter read normal and all warning lights...
View Articlejohn Deere z465... cranks but no start.. help !!!
I bought a z465 mower with the 25 hp kawasaki engine. Pulled it out this year and will not start... put in new plugs, fresh gas, new fuel filter, new ignition switch, new battery, fuses are good, took...
View ArticleScag with Briggs Vanguard 35 blowing fuses
Was mowing today when the engine shut right down. I checked the 20 amp fuse on red wiring and yellow wiring. Both were blown. I replaced to see what was happening. Mower started right up and all...
View ArticleStihl FS 70 Rattle in Shaft
Just bought an FS 70 trimmer and at idle the trimmer shaft has a rattle to it. Once I rev the trimmer the rattle goes away. The rattle isn't to loud but when the trimmer is at idle the rattle is...
View ArticleHelp Please 36" turf tracer motor spurts and dies when blades engaged
Exmark turf tracer 36 pull start with Kawasaki motor.. Mower starts and runs great but I can engage the blades cut for awhile after a few minutes it will start to spurt and sputter miss and eventually...
View Article