2008 Dixie chopper 2550 silver eagle
My Dixie motor shuts down when I release the parking break. I replaced the seat switch thinking this was most likely it no luck I then replaced the break switches no luck where should I look next?
View ArticleDixie Chopper
I have a Dixie Chopper 2750 with a generac engine. Mower was running properly and all of the sudden died. There is no DC voltage when the key is on, the hour meter is even dead. I have started checking...
View ArticleDixie Chopper Silver Eagle Blowing Fuses
I have a 2008 Dixie Chopper Silver Eagle today while mowing my dixie chopper back fired then died. No power at all. So my husband found that a fuse was blown. We changed the fuse and he began to mow....
View ArticleTurf Tiger seat switch
How hard is it to replace one these switches on a TT that is a couple of years old ?
View ArticleClik here to view.
Replace Cracked Ball Valve Sprinkler
Hi All, My sprinkler hookup seemed to have cracked. Is my thinking correct here that I would need to put the copper pipe and work back to the cracked ball valve to replace it then solder the coper...
View ArticleCh25 misfire
My scag turf tiger is dropping a cylinder. It was the first year they made the TT, so it's 17 or 18 years old. Koehler ch25 ser no. 27..... It was popping and missing and I found a blown intake gasket...
View ArticleExmark lazer z dies
I have replaced the seat switch and the brake switch on my Exmark Lazer Z . Motor dies when brake is released or when either of the control arms are moved in . What is next step to take?
View ArticleDeep Fried Scag Mower Deck Spindles
A few years ago my Scag Tiger Cub caught fire and was pretty much completely destroyed. With some help from a donor mower that had been in a highway wreck I rebuilt the burned mower. Between the 2 of...
View ArticleHello I need help with exmark explorer
I just bought and old emark xplorer and does cut ok but is very jumpy ,so I need to advance very slow , so it will not jump up and down very bad it is. also it clogs very easy if grass is little bid...
View ArticleExmark Lazer new motor
Hey guys I have a 2000 Exmark Lazer with a Kohler pro command 26 in it, it has two broken rods and is pretty well shot case is good but that's about it, anyways thinking about putting a new motor in...
View ArticleRedmax Blower Crankcase
Are the bolts on the fan side of the crankcase reverse or regular. Having to replace case cover because of cracked bolts and housing
View ArticleRedmax EBZ 8500 leaking from crank gasket.
I have had two of my Redmax ebz8500 blowers develop leaks at the crank gasket. My dealer warrantied the short blocks and swapped them out with new ones but about 1 1/2 years later they are leaking...
View ArticleScag turf tiger new engine which one?
2007 scag turf tiger the 27kohler on it is bad I can build it but considering new. Thinking 35 briggs vanguard anyone got any other suggestions.
View Articlesolenoid part number lookup
I have a scag tiger cub that has a kawasaki 19hp engine model number - fh580v-c537-r i believe my starter solenoid switch is going bad. My mower will not start and not even attempt to fire and then all...
View ArticleProblems with my Exmark Navigator
I purchased a used Exmark Navigator last year and am generally pleased with the job it is doing.My lawn look great. However there are ac couple of areas I would like some help in.The first is the grass...
View Article36" V-Ride - Hydro Leak
I was planning to sell the V-Ride then had last minute thoughts and decided to keep it. These past two days it's been getting more and more use and I started noticing a puddle of what looks like...
View ArticleClik here to view.
Leveling deck on Husqvarna
I just noticed the front of the deck is sitting lower than the rear of the deck. I need to get it level again. Should I do that by adjusting the nuts on that front adjuster to draw the front of the...
View ArticleLazer Z Fuel gauge issues...
I have a 2013 Lazer and for the first two seasons, the LCD fuel gauge worked great. Always accurate, never ran out of gas. Now the past year or so, it is very inaccurate. Sometimes it'll say its full...
View ArticleSharpen blades while on mower. Cub Cadet 760-ES
Question here about how feasible it is to sharpen my twin blades while still attached to the mower. Cub Cadet 760-ES twin-blades. Such a pain in the ass to remove & sharpen, so wondering if tilting...
View ArticleEcho pe230 won't idle
hey guys, picked up this edger from a friend, been sitting awhile but in really nice shape, i got it running , just cant get it to idle, only wants to run at full throttle, i have put a new plug, new...
View Article