Worth buying old shindaiwa m2510?
I'm starting a business, have most the tools but don't have a trimmer with an articulating blade. I found a 7-8 year old one, guy said it needs a tune up, sputters out. Can get the machine with 2...
View ArticleValve Adjustment on Briggs 280000 Series
Briggs and Stratton Model: 286707 Type: 0413 01 Flat head Valve Specs 0.005-0.007 Intake 0.009-0.011 Exhaust I bought this motor a few years back used. Finally decided to do the valve adjustment. It is...
View ArticleStumped - New ACR - still too much compression (HELP)
Hello- I am hopeful that ANYONE might be able to give me a recommendation regarding a Briggs 20 OHV 331777-2372-g5 with too much compression. I am original owner and all was well until... PROBLEM: Can...
View ArticleVery Hard Pull On Briggs Engine
So I have a Briggs motor that has a very hard pull. What would be the first things you look at regarding this issue?
View ArticleKohler CV740 oil leak
I have a 2005 Hustler Super Z with 1800 hours. It has developed a slow drip oil leak in the area of the oil cooler base. I can't pinpoint the exact location of the leak. It might be the oil cooler base...
View ArticleRedmax EB7001 Death
This EB7001 finally gave up the ghost, well, with a bit of help. I picked up this blower used for $50 in the middle of last season. It wasn't running when I got it but after the carb was cleaned and it...
View ArticleOil Change on Ferris Is 2100 Hydrogear 4400
I drained oil and put new filter on hydrogear 4400. My problem oil doesn't want to drain out of fill tank into hydro unit. What am I doing wrong?
View ArticleGreat Dane hydro pump
I have a chariot Great Dane Needs a right side hydro pump ,whe. U go right just whins? What's the chances it needs a wheel motor ? I checked reservoir with magnet no metal shavings Also are they...
View ArticleZama RB-K89 vs Walbro WYC-9
Which is the better carburetor ? This is why I ask: Echo SRM-266S = Zama RB-K89 Echo SRM-2620 = Walbro WYC-9 Both are 25.4 cc trimmers. Both have sold steel drive shafts. SRM-2620 is the newer model.
View ArticleRepair Advice
Hi guys. My question is about the possible causes of gas shooting out of a carburetor. I bought a used piece of equipment. Ran good, till gas ran through it weak float one day till gas was everywhere....
View ArticleRedmax Carburetor problems and testing/adjusting
Our company uses many redmax backpack blower and handheld blowers including HBZ2610 and EBZ7500. We've had numerous problems keeping them running. I recently discovered that there's a small hole above...
View Article1998 Toro groundsmaster 3000d 4wd transaxle problem
I have a 1998 Toro groundsmaster 3000d 4wd which is driven by a Sauer Sundstrand m15-iht. Inside the iht is a differential with spider gears just automotive differentials. My problem is I cannot find...
View ArticleI've made some Stihl FS90 repair videos
My company has been working with Stihl FS-90R trimmers for several years. During those years, we've encountered numerous problems or things breaking. So during the past several weeks, I've been making...
View ArticleReplacing carb on kawasaki FS481V
Like said above, I'm replacing the carb on Kawasaki FS481V on an Exmark Metro. I can't find any videos but am hoping it is an easy swap. Anything special I need to do? I'm assuming they come adjusted...
View ArticleJohn Deere 737 repower
Ok guys have a quick question. I have a 737 that had a leaking rear oil seal that was run low of oil and has started knocking. I am trying to decide to repower or rebuild. A new engine from John Deere...
View ArticleIgnition tester
Hi just wondering anyone know where to get a good coil / spark tester unit from . My poor old imrie 3000 tester has died .
View ArticleHELP!!! JD 997 Stalling when Handles Engage
I have a 2008 John Deere Diesel 997 ZTrak. It starts up and runs just fine but when you engage the handles into the drive position it kills the motors. The pto, parking brake, seat, and handle switches...
View ArticleUsed Exmark Lazer CT - need help with noise (video of noise)
Bought this CT this week for a really good price. I've got a new belt coming, but can't figure out if this noise is the spindles, belt, or idler bearing. Any guidance?
View Article