Honda bag issue
I have a Honda Commercial HRC2163HXA mower, the top of the line $1,200 push mower. The mower was brand new in August of 2016. I purchased from a man in a neighbouring town a month after he purchased...
View ArticleClik here to view.
What oil do you use? 5w or 10w?
What type oil do you use? I see some of you guy use 10w30, some 5w30, Some Synthetic, some regular.. I've been using 5w30 Regular, but i may upgrade to Synthetic
View ArticleLOVE MY SCAG.... HATE THE KAW... Time for a Brigs ?
OK, i have this 48" Scag Tiger cat 22HP KAW... Love it ! we cut 90 yards a week with that and a 52" Ferris Hydro. First it was a coil pack ,,, then a valve issue ...now 3 days later its blowing smoke...
View ArticleOil change on oil burner
If an engine burns half quart in 20 hours why change oil. This is a 17hp Kawasaki with 700 hours running 20w50.
View ArticleKawasaki FH 641V Choke linkage/Cable broke at choke rod.
Hi friends. I found a post in this forum about using a Kohler plastic choke piece on a Kawasaki FH680V choke rod so the whole Kawai choke rod/plate wouldn't have to be replaced. The original bushing...
View ArticleScag hydro
Hello, having a problem, this is the first time I've used this site so here goes!! I have a 61in scag tiger cat , 26 hp , I am replacing the left hydro pump under the seat, I need to know how to flush...
View Articlex720 Kaw FD750D Chocolate Oil
View attachment 333189 So I am trying to get caught up on my preseason maintenance and started changing oil on our x720 tractor with a Kawasaki FD750D-DS12 engine. I drained the oil and it was like...
View ArticleNeed help. Swisher 2766 with Eaton 778-048's
First time poster here, and first time ZTR owner. I acquired this mower from a neighbor for free because it didnt run and he said the Hydro was locked up. Long story short, i got it running and...
View ArticleHomemade Lift Table
Thought you guys might like to see a lift table that I made. I sized it to be able to handle my Scag Turf Tiger. According to Scag this mower weighs 1250 lbs. The lift table is mostly 2x6 construction...
View ArticleKawi fx600v has a carburetor?
Hello everyone Does the electric start kawasaki fx600v have a carburetor? Thanks!
View ArticleHelp with Clutch on Scag Walk-behind
Hi, I have a Scag 19-HP 52" SWZV Pro-V walk-behind with 78 hours on the meter. There seems to be an issue with the clutch. When I engage then deck drive (cutter blades), the engine dies. The engine is...
View ArticleWalker 26efi fuel pump replace help
Can anyone advise priming sequence after replacing a fuel pump on my 2009 26hp efi Walker. Or a quick step by step, if available. 3rd one to go!
View Articleshaft bolt size on KAWASAKI FB460V?
What size BOLT goes in the bottom shaft of a Kawasaki FB460V-MS14 to keep the pulley(s) on ?
View Articlejohn deere BP45
I have this 1995 vintage model that was very lightly used. It is not the BP45LE. The engine was running at operating speed with the throttle lock on when it was turned off. It would not re-start. No...
View ArticleGrandstand hydro question
Hello, first time on here. I just bought a used toro grandstand 52. the right hydro is really weak in reverse, can this be adjusted? looking at the hydro, when you pull the control into reverse the...
View ArticleSthil 025 Decompression plug
Can you retrofit a Sthil 025 Chainsaw with a decompression release valve ?
View Articletoro 325d wont start
Hi, i hope someone can give me some advice here. I have a Toro 325d. the last 10-15 times i used it it was very hard to start-had to crank and crank. last time it would not start at all. i have...
View Article1998 Toro Groundsmaster 325D is haRD STarting
1998 Toro Groundsmaster Model/Serial 30795-80161 325D With Mitsubishi engine is haRD STarting The glow plugs tested good with a continuity tester. I am only getting 8.93 volts to the glow plugs. I...
View ArticleToro Grandstand -Speed Control Removal Kit
SPEED CONTROL REMOVAL ASSEMBLY NO. 119-7380 I've read on the forum this wasn't a recall, but classified as an update that was free and "replace as needed" on Toro's pocket-book. Does anyone have any...
View ArticleCustomer Return Pallets of Gas Powered Equipment
Anyone delt with these? Customer Return Items from Vendors. Anyone tried and fix them up and either re-sell or use for personal use? Worth it or not? I know a little bit about repairing things (from...
View Article