Oil for foam two stage air filter
Looking to see what people use for oil for their foam two stage air filters? Have a Kawasaki FJ180v and Tanaka TLE 600. Thanks
View ArticleSeating tire
Front tire on my 48" wb popped off the bead. Having a hard time getting it seated. Any tips? Posted via Mobile Device
View Articlewalker mower wont turn over
I have a 96 20hp walker mower with a new battery. When I go to turn it over nothing happens. None of the warning lights come on or anything. If I touch a screwdriver to the power wire on the starter...
View ArticleDuraheat Torpedo Heater Baffling Problem!!!
I figured I'd try and post this here as I saw a previous post with a problem involving their torpedo heater. I've got a Duraheat 125K BTU unit that has me stumped. Since the unit was given to me I've...
View ArticleGas flooding engine
Hi Guys ! I have an '06 Scag swz36 , new engine was put on in late '09 . Since then I've put around 100 hrs on it . Runs really good. Last week I took off the air filter and some debris got into the...
View ArticleStihl equipment not starting
I have 3 pieces of stihl stick equipment 2 of the 3 pieces will not start used them the day before they all have compression only one started What could be the issue I have done tryedeal starting fluid...
View ArticleBoss plow lite
i have a boss plow and the reflector in center of the lights both popped off after hitting a manhole cover How do u remove clear plastic Cover to reinstall?
View ArticleBR 700
Just saw one. Available in my area in a couple of weeks from my dist. Nice. Adjustable large diameter tube. Smooth as glass. Should be in the low $500.00. BR600 lovers can rejoice. Haters can fire at...
View ArticleExmark Lazer Z Blowout promblem!!!
Im about to pull my hair out...I recently purchased a 2012 Lazer Z S Series with 500hrs w/ultra vac collection system. I'm getting a ridiculous amount of blowout mainly from the right corner of the...
View Articlekohler sv600
I have a troy bilt riding mower with 20hp kohler sv600 , the engine surges can anyone help me with this issue thanks rickstringer
View ArticleRock Rake Tines
I have a little 5' 3 pt. Hitch Landscape rake with 4 broken tines. The tines (Standard size 14 X 15") have NO holes in them and clamp between two solid plates. The rake was given to me so I have no...
View ArticleLawnboy Self Propel Chatters on engagement
Hi- I have a Lawnboy 10323 and a 10525. Both units chatter a bit upon engagement of the self propel. For example, if I squeeze the bail slightly to maneuver around an obstacle it chatters, that the...
View ArticleWhich was does this pulley go???
Hello, Everyone, Is there anyone who can help me with the correct orientation of this PULLEY? Mower: 2003 Exmark Lazer Z HP. Motor: 23 HP Kawasaki FH680V Pulley in Question: Exmark No. 1-653035 --...
View ArticleExmark Lazer Z Blowout problem!!!
Im about to pull my hair out...I recently purchased a 2012 Lazer Z S Series with 500hrs w/ultra vac collection system. I'm getting a ridiculous amount of blowout mainly from the right corner of the...
View ArticleHydro pump issues.
Have a hustler z 25hp Kaw.When I cold start the engine I move forward or backward and it does nothing.I let it run 5 or 10 minutes and it will gradually get better back to normal.Took it to dealer and...
View ArticleX 30 won't move this AM.
Its been running slowly and less responsive all week,the belt and cable are good.Looks like a blown trans.Just out of warranty with 800 and something on the meter.Too much to ask from it I suppose.Are...
View ArticleHusqvarna 345FR tuning
Does anyone know the tuning proceedure for the current model Husqvarna 345FR brushcutter. I found a workshop manual, but it is dated 2003 and does not look relevant.
View ArticleCompatibility of Belt-Drive Transmissions?
Hi all- I am planning to replace the transmission on my Scag commercial walk-behind. I have a 20-year-old Scag SW-36KA belt drive mower. (The gears are going bad and after talking with my repair guy,...
View ArticleBlade clutch bearing catastrophic fail on exmark Turf Tracer- suggest brand...
My blade clutch bearing crapped out and made an awful sound on the way out. I have the clutch out and went to ebay to take a peek at cost and it seems there are some aftermarket ones with larger...
View ArticleCustomer Return Pallets of Gas Powered Equipment
Anyone delt with these? Customer Return Items from Vendors. Anyone tried and fix them up and either re-sell or use for personal use? Worth it or not? I know a little bit about repairing things (from...
View Article