Zero-Turn --- Wheel motors not the same
Hi. I'm completely new to zero-turns. Just bought a house with a large yard. Previous owners included his 2008 Toro Z400 with the house. Two things I noticed that I'd love feedback on: 1. The levers...
View ArticleToro 12-32 rear engine drive chain length
So I have an older Toro Wheelhorse 12-32 and I love the thing for using it around the house and cutting some of the neighborhood yards. Well I ran into a ditch, it shifted the rear axle forward on the...
View ArticleHelp troubleshoot whats wrong with 19hp Kawasaki
I have a Lesco stand on mower with a Kawasaki FX600V (19 hp) v-twin electric start engine, the mower has 270 hours. Last week I started mowing a lawn and it suddenly bogged down and quit, it took me...
View ArticleEcho Srm 210
I have a echo srm 210 that will start when i choke it but as soon as i take it off choke it runs for a couple seconds then dies. it was running fine but my grommet on top of the fuel tank was leaking...
View ArticleMaintenance ?
Do y'all change hydro oil/filter belts etc.. At the end of the season or in the spring before new season kicks back up? I figured it would be better to get old oil out of motor and pumps before they...
View ArticleBlower chugs when I throttle it
Got a used stihl br420. New carb, filter, and plug. Today I did one yard and it was fine. Go to my 2nd and it doesn't want run full speed, idle is fine but to run wide open I have to keep squeezing the...
View ArticleThrottle not returning to idle after complete engine teardown
Kohler CH740-0088 in a 2008 Exmark Navigator. Single barrel carb. I removed the engine, tore it down enough to put in new rings and head gaskets. Had the cylinders deglazed, etc. Put it back together...
View Articlekohler dsai conversion
i have a cv740 motor... coil is going out when it gets warm. second coil in 2 yrs... someone told me to da a dsai conversion.... so I google it and find a service bulletin and it says kohler no longer...
View Articletoro 74296 blade clutch
I have a Toro z that I really like. Wire pulled out the male blade connector so I need a new clutch. Where should I look ??
View ArticleWalker mower key broke off in ignition
Walker mower key broke off in ignition. I fixed one years ago but can't remember how I removed the piece of key left behind. Does anyone have a suggestion? Please, I have had so much maintenance cost...
View ArticleGotta have an answer tonight.
Ok guys I'm really losing it here. I have no avail options other than a briggs vanguard 23 hp or a kohler courage 20 hp at this point I could care less which one. It is going on my toro proline 44....
View ArticleDoing your own welding
Hey guys, I have some steel expanded metal mesh I want to put on some equipment ramps. would it be hard to weld it by myself? What kind of welder would I be able to use? I need to cut the expanded...
View ArticleStarting Help w/ Turf Tiger - 27 HP Kaw
I'm new to the site & no mechanical expert- but good basic skills & need assistance I have a Scag Turf Tiger 61" w/ a 27 HP Kawasaki. I had been mowing for a couple hours w/ no incident &...
View ArticleWhere to buy a Kawasaki Replacement Engine
I am looking for a replacement to a Kawasaki FH541V-CS32-R 17 HP engine. I am not sure that this engine is made anymore and I don't even care if it is a Kawasaki. I just want something that is reliable...
View ArticleKawasaki leak oil from bottom main - sometimes
I have an FH 430v that has started leaking quite badly. I mean dumping oil on the ground. It appeared to be coming from the bottom main seal. So, I got a new seal and replaced it. The old seal looked...
View ArticleCarb or EFI on new engine
Well, out of all the trouble I've had with the CV730 engine on my 2005 Dixie, it seems I must have run it low on oil. Rings are shot at least on 1 side. Valves and seats are also caked with burnt oil...
View ArticleKohler command ch25s
Ok I need some help. I have a old lazer 1997 with a Kohler command ch25. We replaced a blown head gasket. Went well but would not start. Checked compression, spark, fuel, then gave up last night. Maybe...
View ArticleWilliam
I have a hustler sport 48" model 929133 run great the problem is when I disengage the blades the clutch spin and ripped the electrical wiring out.
View ArticleBad stator or bad flywheel on Super Z
I have had a used 2008 Hustler Super Z for 1.5 years now with ~300 hours on it (31HP Kaw). Since I have had it I have been unable to keep a battery charged. I measured ~24V coming from stator and ~0.1...
View ArticleNot enough Power to Pto Scag 52 in w/b 18hp vanguard
Hey everyone, I'll try to be as clear as possible and I appreciate your assistance.mI recently purchased a scag 52in walk behind with an 18hp Briggs Vanguard. The Pto won't engage from toggle switch....
View Article