simplicity zt2761 front shock springs
I have a right front shock leaking really bad that needs to be replaced and when I started pricing them I was even more shocked!!!!.. $140!!!! will a cheaper automotive shock spring fit?
View ArticleKawasaki fh 680v hard to start hot
Older engine starts up and runs fine cold but after shut down it becomes difficult to start . It will eventually start after several attempts . If it cools off for a few minutes or so it will start...
View ArticleEcho SRM-280T low power when edging
My Echo SRM-280T trimmer has low power when I try to edge with it. I have replaced the carburetor, both intake gaskets, breather vent, fuel filter, spark plug, & air filter. Any suggestions?
View Articlekohler dsai conversion
i have a cv740 motor... coil is going out when it gets warm. second coil in 2 yrs... someone told me to da a dsai conversion.... so I google it and find a service bulletin and it says kohler no longer...
View ArticleFB460V backfires/stalls
Recently bought an older exmark metro back in may. Ive ran it for over 100 hours then today the idle became choppy and the throttle needle would move back and forth. The mower seemed very weak....
View ArticleDSD 62 Spindles
Hi all, just wondering if anybody known what bearings and seals are in the spindles on 52" and 62" side discharge decks. i need to call my bearing supplier and get some delivered, Regards Graeme
View ArticleTrimmers not lasting!
I am having an issue with weedeaters. I purchased all new weed eaters, edgers, and blowers in December. I switched from echo to reedman to see the difference. Only issues I have are the weed eaters. My...
View ArticleToro SS 5000 home use started leaving clumps, high lift blades and side...
For some reason my ss 5000 has started accumulating grass and then leaving clumps. THis has been happening for about a month now. I've pulled the deck and cleaned everything out from under it. What...
View Articleoptions for getting under deck of stand on mowers
I have one each of WB ZTR and Stand on mowers. Having to access to the underside of the deck to change/sharpen blades on the ZTR and WB I use my Jungle Jack. This will not work with my Grandstand. I...
View ArticleHonda HRX217TDA only going one speed
Hi everyone, I have a Honda HRX217TDA lawn mower that's only going one speed. It has the three speed setting on the adjustment handle. It does move but it seems like it's too slow, possibly stuck on...
View ArticleShin T260 bad vibration and leaving oil residue around engine
I have had my Shindiawa t260 for nearly ten years. Has worked great over the years even after installing the speed feed head. I cut about 2 hours a week on our property with most grass not being overly...
View ArticleTrans Belt / Pulley Problem with Gravely WB
Hi guys, I've recently purchased a used Gravely belt driven walkbehind. It's a 34" Pro-1334G, Model #988122. It's equipped with Pro Steer Handles. I've done a full tune up on this machine and have...
View ArticleToro 52" Cutting Poor
I have a Toro Z Master Z149 52" Model 74173. Problem is it's leaving a LOT of the grass uncut after I go over it! I sharpened blades and tightened the belt and it's not doing much better. Any ideas?...
View ArticleGravely pro 150 WB
So I had the opportunity to "test" a 50" WB Gravely Pro 150 with sulky. Now when I say test, I think I might have only operated it for 1 minute, and this was the first time I ever touched a commercial...
View ArticleHustler / Landpride Hydro Drive belt replacement
I have a Landpride Z72, which is a re-branded Hustler mower. My hydro drive belt has started slipping and I had the replacement belt already. When I went to remove the old belt, it was still tight...
View ArticleLesco 48 belt drive drive belt
Just purchased a lesco 48 belt drive Walk behind and noticed the drive belt from the motor to the transmission has a small section missing. Does anyone know the correct part number or exact length and...
View ArticleWright 52" fx600v problems
Help appreciated. So I have a wright 52" with the Kawasaki fx600v. I been having issues with it sputtering when it's up to running temp. I can get it to sputter briefly just by quickly bringing up the...
View ArticleHonda "clone" engines???
Does anyone have any experience with the Honda "clones". I believe they are manufactured in China, and marketed under various names, but they are generally blue, and sold at places like Northern Tool...
View ArticleMy JD ZTrak 757 Repowering Experience
Just and FYI to hopefully help someone else going through something similar. Bought a used JD 757 3 years ago. Back then it had a rebuilt engine and new hydraulics. I use for residential only. Put 30...
View ArticleKohler CH740 Crankshaft Spline Lubrication
Does anyone know how to perform this? I have the engine apart, putting new rings, seals, etc. in it. Just curious if I should perform this task while it is apart. Not even sure what it entails.
View Article