Walker Hydrostatic Drive-Rebuild?
I am still trying to determine if a Walker Hydrostatic drive can be rebuilt. I have learned it is built by Eaton. My Walker manual shows some parts for the input shaft side(gear/bearing/seal etc.). It...
View ArticleIf you could only have ONE socket set would it be a.....
1/4 inch drive 3/8 inch drive 1/2 inch drive
View ArticleBriggs Vanguard swap questions
Hi all, I'm attempting to install a Vanguard Big Block I picked up. The engine is model 613777-0001-J1. I am trying to figure out all the colors on the wiring harness. The connector is an 8 pin with 5...
View ArticleLawnboy 2 stroke carb question
It's a lawnboy 2 stroke duraforce engine, model 10323. Anyways really don't use it much, here at the house but last yr re-did the carb, as was not running right, symtoms, pointed to the carb. Forgot...
View ArticleCurved shaft trimmer to a straight shaft?
Someone gave me a curved shaft echo the old ones with the gray engine can I take the curved shaft off and put a straight shaft on it
View ArticleSpeedi Sleeve
If anyone ever encounters a worn shaft from a seal wearing into it, there is a solution other than replacing the shaft. It is called Speedi Sleeve and is a stainless steel sleeve that is installed over...
View ArticleKawasaki 17 hp twin 500 v
A buddy brought me a EX Mark ZT with the Kawi 17 hp twin. I haven't dwelled on it all that much since we have been under the gun with all this bad weather down here in Louisiana. He started it and went...
View ArticleFH531V runs rough under load after 10 min
I have a Husqvarna ZTR with a Kawasaki FH531V AS05. Crank it cold and it runs great for the first 10 minutes. After that, it starts sputtering when I put it under a load by thrusting forward quickly on...
View ArticleFerris 3100 belt update
I am not a lawn care business owner. I cut about 12 acres of private land. I have owned a Scag Turf Tiger for over 15 years. It has proved to be a rugged piece of equipment. However, last year I had...
View ArticleV ride deck not level
Have a 2015 Scag VRide 48" floating deck mower, and only 3 of the deck chains have tension on them, which makes the deck pivot and not sit the same height off the ground on each side..Can't figure it...
View Article19 Kaw Vibration Problems
I have a 19 Kaw FH601V. It's on a Bunton 2190. Motor has around 900 hours on it. Last year I noticed a weird vibration in the motor. Now this is not where the motor shakes or surges, as if the carb...
View ArticleGot new Craftsman hedge Trimmer 28cc 22"
Man, first hedge trimmer ever own and got more power than I expected it I mean more than enough. It very powerful machine. It trimm thick brush like a butter
View ArticleKohler 20HP Not Shutting Off
My Kohler 20HP 2 cylinder engine on my Ransomes ZT100 is not shutting off when I turn the key to off. Once cylinder shuts off but the other one keeps going. I dont know how this coil circuit works. Is...
View ArticleFerris IS2100z Question
On deck spindles how much grease do you put in them? There is a plug on the bottom of spindle housing does these get greased to. Does this type of spindle use a tapered bearing?
View ArticleKawasaki 20hp vertical leaking oil
It looks like it's leaking from a plug in the sump.Anyone know to fix this easy or is this a major repair?
View Articlekohler bb. what 20-50 oil?
brand new. ecv980 What do you think about when i should change the oil? and when i do what oil would you put in it? break in oil??? how about when can put full synthetic in?
View ArticleGood Info about Oil.
Hey guys, (and Envy in particular) I found this website that give the straight skinny on oils how they are made and why one type is better than another. It also dissects oil filters and why we should...
View ArticleElectrical problem
04 DC 27hp kohler. I cannot get this machine to start unless I jump it. Battery is testing good. Past two years I've had to but a new battery at the start of the season. Works fine for a few weeks then...
View ArticleChute Question
I am in the market for a few chute blockers. I am curious if anyone has ever used the Advanced Chute Cover from Ballard INC? These will be going on a 54" Big Dog 36" Snapper Pro 36" exmark any...
View ArticleTank M60 Power Issue
Looking for a little help, I have a tank m60 with the kohler commander 27 hp motor. while cutting the grass at high throttle from time to time it will throttle down for like a minute or two by itself...
View Article