Patching hole in plastic gas can
JB weld doesn't hold and neither does gorilla glue. View attachment 325954
View ArticleRed Max Trimmer Bogging
Bought a new red max trimmer this year as my echo finally bit the dust. when completely warmed up, it occasionally bogs to the point where I have to feather the throttle to bring back the RPMS, then it...
View ArticleGovernor limiting to 3300 rpm?
I just picked up a 61" Scag SWZ hydro last week that needed some work. It ran rough, but ran with year old gas. Hydros are tight. I did the following to get the FH641v running right, but it is limited...
View ArticleSharpening blades on 48" scag tiger cub
I've sharpened the blades on my mower with a grinding wheel 1st then after seeing how bad they cut I did it with a flap disc and it's still not cutting good. The blades are newer too. Any suggestions...
View ArticleBillyGoat PL2500H
I purchased the PL2500H non-hydro aerator. It has three ranges for speed; High, medium and low and is mechanically driven. My problem is that the machine goes the same speed in all three ranges. I...
View ArticleKawasaki fx801v
hello guys! I was wondering if any one knows how to set the rpm to wide open. My throttle cable is opening all the way but I'm only getting about 3100 rpm with no load. Any help would be much appreciated
View ArticleGravely 260z brake job
I have a Gravely 260z (992088) mower and want to change the brake pads. I have the wheel off. What's next? Do I remove the big nut in the center of the hub? If so, what size socket is it? Any info is...
View ArticleNo compression.
I have a FH541v engine I am working with. Guy brought it to me because of low power, did a compression check, has 60psi in the left cyl, 0 psi in the right, popped the valve cover to check them and the...
View ArticleHonda HRX17 mower - increase rpm
how do I increase rpm on Honda HRX with GCV 190 engine. It is only turning about 2800 rpm
View ArticleStihl FS90R replacement head
i dont like the head on my new FS90. I tried to replace it with speed feed head and none of the adapters worked looks like the FS90 arbor is a fine thread 8mm or at least it is finer thread than my...
View Articlegravely 1336 tire replacement
Hi guys need help again. Ho do you remove the rear wheels to replace the tire. I have a 36 inch gravely belt drive with pro star shifters. I have taken the snap ring off one side and the wheel will not...
View Articledecarbonizing br600 questions
Appreciate in advance any help as never git around to performed this task but planning to pick up a bottle of the solution next time i'm near (Edina acid or something hopefully he'll have it) but...
View Articlegood machine poor engine
i had to always repair a ever ride hornet. the engine did not even make 300 hours and dropped pushrods.
View ArticleRiding mower John deere GX 85
I hit a rock and stalled motor. Won't jump off. Turn key and nothing. I replaced battery with new one. Also replaced starter switch,starter relay and a new starter solenoid. Now can jump start by...
View ArticleBest lubrication grease for spindles?
I have a IS3200 Ferris 61" deck. Sorry if it's been beat to death but I am wondering what is the best deck spindle grease. I did find in a couple places where guys like Lucas Red n Tacky. I'm new to a...
View ArticleGrasshopper 725 Surging
Hi guys, New to the forum and seeking maintenance info. My 91 725 has been a "TANK" and the Kubota gas engine has been trouble free. That is until recently. The engine has started surging and now it...
View ArticleStihl 4mix broke valve, replaced, need help reassembling
My FS110R broke a valve and I replaced it but now I need help putting it back together.. specifically: How do I get it lined up to open and close the valves at the right time?
View Article2008 Dixie Chopper 27?60 Classic Gearbox and Pump issue.
T-Box down shaft is just spinning and the gear is not turning , also took off the left side pump off and the splines worn down and sharp. My question is can I rebuild the gearbox and if I have the pump...
View Articlegravely oil change interval
So I noticed my gravely owners manual says nothing about changing the oil, so I went ahead and just followed the 100hr oci that it shows in the engine manual for Kawasaki. Apparantly on the hour meter...
View Article