UNEVEN CUTTING ON GRASSHOPPER735BT WITH 3461PF
HOPE IM IN THE right place i have a grass hopper mower which I love but has started to cut uneven by 3/4 inch checked tire pressure and its good wondering should i check other things before I try to...
View Article2007 Walker GHS MT pto gearbox help
The pto gearbox (I believe Walker part #8050) is bolted to the frame with 4 bolts which go up through the frame into the bottom of the gearbox. About 2 months ago the bolts must have gotten loose......
View ArticleBobcat Leo Model #942282 - need transaxle
Have a Jacobsen built Bobcat Leo zero turn. The right transaxle is frozen. the transaxle itself is part number 4129341 which is the updated part number (original part number was 778-043). New unit...
View ArticleCub Cadet Advantage Z- Force S with Kohler 22 V-twin OHV 725cc flooding inthe...
The engine is model SV715-3029. The mower ran then stopped. Flooded gas in combustion chamber. Checked the air breather and no gas. A couple of hours later the air breather was almost half full of gas...
View ArticleKAWASAKI 14hp
Having a spark issue with this engine. Two questions. 1:Should there be power going to the igniter/ignition module with the key in the on position? 1a: Starting position/cranking? 2: Is there a way to...
View ArticleGravely Promaster 300 Won't Start or Run
Mower has a Kohler 20hp V twin engine. I believe that I have narrowed the problem down to the seat switch circuit. I get no continuity when I ohm the wires at the switch. I do have the schematics for...
View ArticlePossible to fail compression test and pass leak-down test??
I'm a school teacher and moonlight mechanic and I have a project that is currently stumping me. I'm working on an 8 year old (approximately) Everide Warrior with a Kawasaki FH721V-AS32-R with about 400...
View ArticleExmark Lazer 27 HP Kohler
engine runs fine then sometimes the rpms drop way down. If I wait for a little while it will throttle back up. Took it to a dealer last year and they said it could be several things. After $750 and now...
View ArticleExmark lazer z won’t start
LZ27KC605. 67000 serial. Try to start and only hear a faint click near the starter. Replaced the starter and still the same thing. Engage the PTO tontry and heat the loud click in the back. Any ideas?...
View ArticleHusky BP150
I have a Husky BP150 backpack blower. It starts great,1 or 2 pulls no problem. Buy recently it will not rev up as soon as I give it any throttle it starts to bog out. I'm not very good with carbs so...
View ArticleLow oil light comes on
Hey Everybody, I'm new here, thanks for all the great info on this site. I have a 2012 Hustler Fast Track SD with a Kawasaki FX730V engine. At only 40 hours the low oil light started coming on at low...
View ArticleHow to change mini skid tracks
I am going to need to be changing the tracks on my vermeer s600tx mini skid soon. Anyone have helpful insight or a website that I can consult to go about this?
View ArticleHG hydro pump assembly orientation questions...
Hey All. I recently resealed my leaky BDP-10 pump in my Scag and all works well. While I was working I came up with a few questions. I get that the charge cap goes on one way or no worky. I figured...
View ArticleSharp blades to center
Has anyone ever heard of people sharpening their blades all the way to the center.
View ArticleCub cadet 48 bad deck vibration
I went to mow tonight and I couldn’t get the blades to spin. Turns out underneath was full of gunk and needed to be cleaned out. I cleaned it out and now the blades spin fine but the mower deck has a...
View ArticleJD WG36A Walk-behind Transmission Problem
Machine: 2013 John Deere WG36A (36-inch belt-drive walk behind) with only 20.1 hours on it. I believe I may have a problem with my transmission, because all of the belts seem to have the correct...
View ArticleHow much can I sell you Cub Cadet push mower for
This is probably not the right forum, so, sorry. Couldn't decide which one was best I just bought a 2010 Cub Cadet push mower that needs works. How much do you think I should charge once I get it...
View ArticleDeere LX176/B&S Intek 19 Swap Help
New to the forum and am looking for some electrical advice. Trying to do: Swapping an Intek 19hp engine into a Deere LX176 and am looking for some confirmation as to the wiring connections before I...
View ArticleNeed help with scag SW-48 with kawasaki FC420v wiring and PTO
Hey everyone, I recently purchased an incomplete scag walk behind (sw48 14kh) with the kawasaki 14HP FC420v-KS09. The mower is set up for an electric clutch but the wiring harness is incomplete and the...
View ArticleHustler Super-Z Pulley/Clutch removal
Thanks to everyone who gave me advice and suggestions on whether to do a short block or full replacement of my Super Z’s engine, a Kohler CV-750. I opted to spend the extra money and do the full...
View Article