Hi, new here. Just trying to get help. My Kohler 18 hp motor will not start
I just replaced the carb on my Kohler 18 hp model number cv493s. The motor still will not start without pouring gas into the carb but when I stop it dies. Please help!
View ArticleRedmax 7500 BP blower rebuild kit?
Where could I find a complete rebuild kit for a 2013 RedMax 7500 backpack blower?
View Articlekawasaki fx730v starter problems
I have 2 customers that i know of that there units starter solenoid clicks but engages the ring gear intermittently when one keeps turning start switch to crank the engine to start and run. even with...
View ArticleCan I use 5W-30 oil in my Kawasaki FJ180v Push Mower?
Cam I use 5w-30 oil in my Kawasaki FJ180v push mower? It is a snapper.
View ArticleAir in hydros
I installed new wheel motor on Toro zmaster and the wheel still won't move. I jacked it up opened the relief valve move levers back and forth for a few minutes then tighten them back move back and...
View ArticleNeeding help.
I recently purchased a simplicity 33" zero turn. I realized the blade holder is bent and needs replaced. Is the center nut the only thing holding it on? It is coming off very hard. Thank you..
View ArticlePurge bulb mystery (to me, at lest)
Stihl FS55R weedeater. Put new carb (Zama S97), lines, and filter on it and pressed the purge bulb around 7 times,. No fuel appears in the bulb. So to test further, I removed the carb and attached...
View ArticleFS 85 weedeater wont start
On my FS 85, I verified spark by pulling plug and grounding against case and saw spark. gas bubble pumps up and appears to be getting gas. Any ideas on what and how to check anything else? Thanks
View ArticleBobcat 630 steering problem..
Hi everyone, So my father inherited an old bobcat 630 which he spent some time cleaning up and making repairs to.. we dont use it for business, but its a helpful machine to have around. A while back...
View ArticleFilterMag
I just purchased a new mower with a Vanguard motor, 2 hours on it now that I cut the weeds. I purchased a pair of FilterMag magnets that I installed on the oil filter. Supposedly these very strong...
View ArticleReplace Scag Deck?
Was wondering if anyone had replaced the deck on 61 inch turf tiger. I have one with 2000 plus hours on it and everything works fine on the mower but cut is not good. The deck has a pretty good size...
View ArticleTiger Eye Oil Pressure Indicator?
Scag Owners! With the tiger eye oil pressure guage where does it read? I have the 29efi Kohler and none of the bars are lit up on the oil pressure indicator. I have 7hrs on it and it hasn't used a drop...
View ArticleGas in exhuast
One of our Kawasaki FX, 691 I think, has been hydro locking on gas and when it finally turns over it spits gas out the exhaust. It only happend after it sits the night. I checked the float level and...
View ArticleCut issue with Scag Tiger Cat II
I have a two year old Scag Tiger Cat II with a 61 inch deck and a 26.5hp Kohler EFI. Last season I noticed that there was about a 3 inch strip essentially located between the middle blade and the...
View ArticleExmark commerical 30 Aluminum Idler Pulley
Ok, so i now have 7 of these machines dating back to 2013. The two newest ones i have have what appear to be aluminum idler pulleys with aluminum caps (instead of the brass colored ones with the black...
View ArticleReplacing idler pulley (s) on exmark 30
This thread seems to say you can just replace the pulley with the new version. An Exmark service bulletin attached shows other things being replaced at the same time, such as the bracket. Has anyone...
View ArticleBriggs 20hp
Got a briggs 20hp v twin engine today seems it has ran very low on oil . drained the old oil replaced oil filter started straight away but it has loud ticking noise the more rpm worse it gets .Any...
View ArticleHalf or full throttle to engage PTO?
I just snapped the deck belt on my 50” Exmark Laser HP. 27hp Kohler. I picked it up used a couple weeks ago. I’ve only put about 5 hours on it. The little label by the PTO switch says to engage blades...
View ArticleNeed help with scag SW-48 with kawasaki FC420v wiring and PTO
Hey everyone, I recently purchased an incomplete scag walk behind (sw48 14kh) with the kawasaki 14HP FC420v-KS09. The mower is set up for an electric clutch but the wiring harness is incomplete and the...
View ArticleKawasaki fx730v will not turn over after long periods of u
I have a husqvarna PTZ-54 zero turn with a Kawasaki fx730v. The issue only seems to happen after the mower has run a while. If the engine is cold it will fire right up. But after mowing for more than...
View Article